Search results for query: *

Hi, now i have the pinout, the self built cable works fine, but i have the wrong software version from the diag software. my printer (phaser 360) is v9.28 and the diag software is v9.16 it works but sometimes the printer's processor gets an overflow during the tests (error code 00.03....)...

has anyone the diagsoftware for the phaser 360 firmware v9.28??? i need it to repair and verify my printer thanx

hello, i got a tek. phaser 360. first it had the error 5,002.42 (0x2b03): YA_POS_FAIL i repaired it by replacing the two motor driver (lmd18201t) on the power board. the error came every time during warm up and while i was searching for the error they blew. i replaced them with 2 new. now the...

hey bryan, i wrote an email to the sender's address of your email(cox) i do not know, why you did not get it... i sent the mail again, hope, that you receive it now chaos

hey bryan, when you search in the main page (on the left) for phaser in services (dropdown) then you get the one and only result. it is in san francisco under computer services hope you'll find it thaaanx, chaos

hey bryan, thats a nice idea, but how can you give me the software??? the problem is, that i can not post any address... its always deleted by an administrator. here is no private messaging system, so we can not get in private contact to change the addresses. another try is dirkandre ad...

fine... i postet my email address but it was deleted by an administrator... can anyone tell me how to get the pc based diagnostics??? here is no private messaging system to send a mail address to get the software... i need the software to verify my self built cable... please help us

thanks... this was very very very helpful.. a max233cpp is a converter for the rs232 conversion with low powered devices... i have got one... u can order samples by maxim (does not cost anything), you can order one and get two... can u tell with what pin of the ic the diode is connected and...

hello again, now i measured the voltages by powered on printer (in service mode, but is the same as in normal mode) 1=tx/rx= 4,96 volt (unstable, when i touch the gnd with the other hand (resistance-connection to gnd), it goes to 4,93 volt) 2=n/c= 0 volt (n/c) 3=5v= 4,96 volt stable 4=tx/rx=...

hello, i measured the pins of the service connector from my tek phaser 360 board... when u look from the panel, where the connectors are: 1 2 3 4 5 ------------------ | . . . . . | ------------------ Service Only there are: 1= tx/rx 2= n/c 3= 5Volt 4= tx/rx 5= gnd how can i...

hey marty, can u plz make a high res photo of your service-cable-pcb from both sides? i need this cable but i read that it costs about 130 and that is too expensive. i want to repair my phaser 360, it has the error as described in the thread http://tek-tips.com/viewthread.cfm?qid=910955 you...

oh oh oh, i need this cable and software, too.. i searched via google and yahoo but did not find the pinouts... someone in this world must have the pinouts... plz reply hhhhhhheeeeeeeeellllllllllpppppp

hi marty, thx for your answer. after calibrating the drum position (one rotation of the big alu drum) and, if position is not correct, it corrects the position of the maintainance assy by the solenoid on the left. it only clicks one or two times, until it is in the right position, so the...

hello, sorry for my bad english, but i'll do my best. i got a tek. phaser 360. first it had the error 5,002.42 (0x2b03): YA_POS_FAIL i repaired it by replacing the two motor driver (lmd18201t) on the power board. the error came every time and while i was searching for the error they blew. i...