Brand new Cisco ASA 5506-X. Ran the VPN wizard to enable Remote Access VPN with the Cisco VPN Client. At the end, all is "OK" except an error:
Error: crypto ikev1 enable outside
failed to open "udp/localized/2/4500"
Error: Error opening IKE port 4500 on Interface outside
Can someone help me...
Does this affect many websites at Site A? No. Just one website in particular. Has been this way ever since switching from Comcast to Fiber. We are almost to the point where we are going to assign an entire new IP block to the customer because of this. We contacted the ISP for fiber and this is...
We have two sites -- A and B -- connected via a persistent IPSEC VPN tunnel.
Site A is trying to get to a website but it takes almost a minute to load.
Site B can get to the site just fine. The page loads instantly.
Is there a way I can make requests in site A for this URL go through...
Last question. I just want to clarify what "nat (inside-wlan) 1 0.0.0.0 0.0.0.0" actually did. Is it basically creating a default route for that interface, and does 1 represent the "pool ID"?
Many thanks again. I have been posting on Cisco forums for months but I just get drive-by "try...
Wow! Thanks for the quick reply iggsterman. Should I remove the second static line then, or leave it and add the nat line?
I can ping the gateway from the 192.168.100.1 network. From what I understand if I make the security level the same on eth0/2 (100, just like eth0/1), it's technically not...
I have an ASA 5510 and just configured eth0/2 as 192.168.200.1 to expand my network -- I would like to just put all the wireless access points on this new network. I don't have much CLI experience but have been using ASDM for the last couple years and have managed to figure out how to do quite a...
Hello,
My building has two internet connections, fiber and Comcast.
I have a computer plugged into the Comcast and assigned a public IP to it. I copy files from this computer to a server behind a firewall on the fiber, in the same building. The transfer rate is very low and I was wondering if...
Thanks ShackDaddy! I agree, a flat domain structure is always nice. I tried to demote the server dc.subdomain.domain.local and got an error immediately after it started:
"8614 The directory service cannot replicate with this server because the time since the last replication with this server...
I forgot to mention, AD Sites and Services is currently set up so I imagine I'd need to decommission it or remove the site from the main site's side first? Not sure how to "turn off" AD Sites and Services properly. Can I just go into the snap-in and delete the west coast site?
Hello all,
I have two sites connected via persistent site-to-site VPN.
West Coast is the "main" site --> domain.local
East Coast is the "remote" site --> subdomain.domain.local
For some reason, the remote site was created as a subdomain and a DC was put in place as dc.subdomain.domain.local...
On my Exchange 2003 server, I access OWA using http://servername/exchange/administrator/.
If I replace administrator with another username, I am prompted for credentials even though I have full control over the "server" in Exchange System Manager AND the Mailbox Store -- both are FULL CONTROL...
How about a group policy or a batch file to just empty the temp folder(s) at startup, shutdown, or every x amount of hours? Yes, not the best solution but at least it's something to buy you some time....
A better way to do it (if you know how to program) would be to stream the file. Store the...
Thanks Denny,
I wasn't notified by email that you responded to this question, not sure why when I clicked E-Mail notification. I will post my question in the SQL admin forum. As for keeping the website files in sync; sounds like rsync will be the easiest. I'm familiar with DFS -- never set it...
Hello,
I have a few servers in San Diego which we are going to mirror and set up on the east coast for load balancing/redundancy. Is there a way of configuring mirroring within IIS, or is another program like rsync necessary? Also, same with keeping the databases up-to-date. Sorry if I posted...
Thanks NetworkTek, Cabraun, and ArizonaGeek. I'm going to coldclone the entire server, but only as a backup. I'm going to create a fresh VM and do what ArizonaGeek said. I'm sure it goes without saying a server that YOU install is perfect because you know what's been done to it. With a server...
Cool, thanks that does help. I feel more comfortable knowing you've done multiple SQL servers and not just one or two. So just by stopping all SQL services, the DBs are unmounted then? Also, I've never done an offline p to v, is that something during boot up? Regarding the array, that is what I...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.