Search results for query: *

Help, My phaser 850 jams every time from the main tray though it can print fine from the manual feed. The paper goes in about two inches and when I pull it out there are holes on the paper on both sides looking like slits where it ripped on the way out. Is this a paper tray problem or a pick...

Help, My bosses phaser 560 leaks toner onto the paper transfer kit near the replaceable paper feed roller. It always prints out colored spots on the paper. I clean it all the time, then it prints clean for 2-3 prints then it gets dirty again. Why is this happening? I looked at the toners and...

Help, My phaser 780 cannot feed paper at all from either the lower paper tray or the multipurpose tray. I took into service center, and they said i needed rollers for both trays and seperator pads for the mpt. The printer only has 20k prints on it. How long could the rollers last. Is is worth...

Help, My phaser 360 cannot print blue at all, all other printhead are fine. WheneverI do a cleaning cycle, the blue printheads turn on and off randomly. All are off except for two or three. When cleaned those would turn off and others would turn on. It seems that the printhead can print but...

I just got a used phaser 780 but it is missing it's fuser handle door lever. After unsticking the fuser assembly, someone stuck an aol cd in the fuser assembly. Now it states that there is a jam at C,D. I cannot find anything, there is brown looking toner around the fuser assembly. What sensors...

Ok, I fixed the error 30 now I get fuzzy images on my pictures as well as vertical streaks that run along the paper path. Could this be cause by an overexposed imaging unit from a lighted room? (I took out and reset the imaging unit several times and left it out to clean the sensor.) Did I...

Help, I got a phaser 750DP. It was shipped to me with the imaging unit and toners inside of it. It was heavily toner bombed. I cleaned up the inside and I when I turned it on I heard a clicking sound like a switch was trying to turn on. Then I got the error 30 code. It said to first reset the...

I have used 100lb Xerox glossy laser printer paper on my 560 with good results. I bought at OfficeMax by the piece for 5 cents each. They use them in the Docucenter models. It works fine in the Phaser 560. Adrian

I have a phaser 750N. I need a code dimm to upgrade it to a plus model. Does anyone know where I can get one for around $200? Xerox wants $300 for one. Thank you, Adrian

Ok, I finally got the printer up. But it stays in intialization mode and keeps printing out bad test pages. This is what it was like before I spilled the ink. Why is it doing this? Why cannot it go into ready mode. I though it was doing this because of a bad network card. Or is it a bad print...

Hi, I am thinking of upgrading my phaser 560 with an 740P or 750P. Is there any difference in the print quality or is it just faster due to the processor or extra memory? I use this for graphic design plus doing occasional digital photo prints on glossy paper. Would upgrading make any...

Hi, I looked for the alignment marks but I could not find them, I think they are aligned but it still gets stuck during the cleaning around 40% or 66%. All of the is becuase of the ink spill. I cleaned up all the ink. Onthe CAP assemble there is one thing I noticed. There is a long H shaped...

Thank you for the tip. When I opened the printer, the CAM head was not stuck to the print head. It has difficulty going down but not up. I have tried to clean the cap wipe purge assembly and help it to move freely up and down. So far I got to 66% before I get the 8,001,44 error. What can I do...

Hey, I bravely opened up the printer and saw that the moving vacuum head was stuck. I try to move it up and down with the gear and it gets stuck in several places. I cannot figure out what is getting it stuck? Any suggestions? Also, when I opened up the printer I fount magenta ink all over the...

Hi, my phaser 350 just started to get this error but it never goes away. My maintance tray is jammed. Can I fix this myself, if so, how do i do it? adrian

Help, I bought a 350 that was supposed to have good print heads. It was in storage for several months. When I put some ink in it, it kept printing out cleaning pages. Every one looked the same. There was no difference. It would look like red and white and black stripes. The printer would never...