Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. kgornek

    Last Software Release for NEC 2400 IMX

    Thanks!
  2. kgornek

    Last Software Release for NEC 2400 IMX

    Can anyone tell me what the last software release was for the NEC 2400 IMX? I'm currently on release 8 from 8/9/2000. [neutral]
  3. kgornek

    M3903/3904

    Or just T/R?
  4. kgornek

    M3903/3904

    I assume by "all phones" you mean Nortel M phones? Because I know all the NEC phones in my office use straight line cords.
  5. kgornek

    M3903/3904

    Can someone tell me if the M3903 and M3904 phones (on the Option 11C) take a straight or reversed line cord please? I believe I ran into this issue a long time ago on a Option 61C with a M2616 phone and I'm pretty sure the line cord needed to be reversed. Or am I just getting old and losing my...
  6. kgornek

    Activating CFW feature in 11c

    If I change the cfw key information, is there a way to remotely activate it? It's to a external number and I do have CFXA for a CLS I changed it in LD 20 CHG 3904 yes key 19 cfw 16 912301231234 I changed the button but how do I activate it remotely?
  7. kgornek

    Is Inbound Caller ID Name on the NEC 2400 IMX supported?

    Can someone tell me if the NEC 2400 IMX will support inbound Caller ID with name? We currently have the inbound number only and I've had requests for adding the name feature as well.
  8. kgornek

    Toshiba CIX-100 - Extension Appearance Question

    I’m looking for a solution or alternative to having two keys for a single extension appearance on a non-primary phone. For instance, a secretary would like to have a button on her phone with her manager's extension on it to see if he is on the phone, answer his incoming calls, and be able to...
  9. kgornek

    NEC 2400 IMX - ASYDL Command

    I just needed the right manual. Found it. Thanks.
  10. kgornek

    NEC 2400 IMX - ASYDL Command

    Does anyone know where to find all the index meanings for the ASYDL command in the 2400 IMX? I've looked through all my manuals and can't find anything outlaying what each of the sys/index represents.
  11. kgornek

    2400 IMX IP address

    Thanks for all the good info. I'm going to do some more research on the Octel. As far as the 2400, everything I've read so far states needing a non-load restart, but if there's another way, that would be even better.
  12. kgornek

    2400 IMX IP address

    Ok, there is no available ADTM command but I did look at the ASYDL command and now realize how to set the IP, Subnet, and Gateway addresses. Just a few questions: Will this affect my direct connection to the terminal in the room on the IOC port? I read that I will have to perform a SINZ...
  13. kgornek

    2400 IMX IP address

    I have two network connections to each of my SN1455 CPRAQ-A cards going to a network Hub and was wondering if there was a way to access this PBX via an IP address with MAT software? Is there a command to find/change the programmed IP address for access? There are no IP phones on this PBX as it's...
  14. kgornek

    Unassigned Numbers on NEC 2000 IPS

    I have a group of DID's that are assigned to me by the LEC but not assigned in the PBX. Whenever you call one of these numbers it routes to the main console instead of a fast busy or a unassigned recording. I looked at the translations and can't find anything that would route it here. Any...
  15. kgornek

    NEC Elite 192 - LD Dialing Connection Delay

    That worked! Thanks.
  16. kgornek

    NEC Elite 192 - LD Dialing Connection Delay

    I have a NEC Elite 192 system and my users are complaining about long connection times on LD dialed numbers. They are stating that after they dial a LD number, the amount of time it takes for the call to connect is 6-7 seconds before they get ringback. The connection time on local calls is only...
  17. kgornek

    Octel Access Confusion

    So I'm a bit confused on the Octel access levels. We have the Serenade models and I'm not clear on how to access the different levels. (Administration, Maintenance, and Report) Does it all just depend on the password you use? I only have one password but it will not allow me to perform the @ps...
  18. kgornek

    Looking for Octel Serenade Manuals

    I have an OCTEL Serenade 200 with the 5.4.0.0-2 S/R and I am looking for some installation/maintenance manuals. I found manuals titled Serenade 2.0 and 3.0 but I'm not sure if this will apply to my 5.4 software release. Can someone please assist with pointing me in the right direction for some...
  19. kgornek

    Intercom in a 2400IPX

    Can anyone assist in setting up a intercom in a 2400 IPX? I see intercom assigned in the AKYD command but have no idea how to edit, creat, or change them. It seems to me that each ICM would be assigned a ID per phone, but I can't find anything to connect the dots. Here are the random commands I...
  20. kgornek

    ACID Command - NEC 2400 IMX

    I ran with those parameters and actually had it work. The only glitch was the block call was pushed straight into the VM box for that number. I was hoping to block the number from the PBX entirely so they couldn't call into the main number which terminates on a attendant console.

Part and Inventory Search

Back
Top