Search results for query: *

I will try it tonight and let you know. Thanks, Jose'

50.5 is a PIX 506 firewall. I was thing of using the track option to solve this problem. Thanks, Jose' Luis Granda

Here is the configuration, Current configuration : 2520 bytes ! version 12.4 ! boot-start-marker boot-end-marker ! logging buffered 51200 warnings ! no aaa new-model ip cef ! ! no ip dhcp use vrf connected ip dhcp excluded-address 192.168.50.1 192.168.50.59 ip dhcp excluded-address...

Correct, My internal network is 192.168.50.0. Would you like a copy of the router configuration. Let me know Thanks, Jose Luis

The main internet access is through the internal network. the route is as follows, ip route 0.0.0.0 0.0.0.0 192.68.50.5 this is the main internet connection. Thanks, Jose' Luis

I need help on getting the following application to work. I have a Cisco 1841 with two Fastethernet. One of the FastEthernet 0/0 is connected to my internal network, Fastethernet0/1 is connect to a satellite modem to the internet. I need to have two default routes. the default routes are as...

sbonete, I appreciate the help. That work with no problems. You are the man. Thanks, pepe

Thanks sbonete. I will try this this week and let you know. Jneiberger the peer never establish until I delete the static route. BGP nevers gets an update.

The bgp session remains down until I remove the static route.

Sory, I made a mistake on the list of IP address. The 197.98.10.0 is on the eigrp. All the routes with the 197.98. address are learned via eigrp. I hope that answer your questions.

Here is the information Master#sh ip bgp BGP table version is 232, local router ID is 206.115.42.162 Status codes: s suppressed, d damped, h history, * valid, > best, i - internal, r RIB-failure, S Stale Origin codes: i - IGP, e - EGP, ? - incomplete Network Next Hop...

The routes are 197.98.4.0,197.98.6.0,197.98.10.0,197.98.14.0. Those are the locations that have been converted to PIP.

Here a copy of my config. version 12.3 service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname Master ! boot-start-marker boot-end-marker ! logging buffered 51200 warnings enable secret 5 enable password 7 ! no aaa new-model ip...

This network is not going to the Internet. This is a private PIP network from MCI. MCI uses the bgp and the eigrp is my old network that I am converting from. Both are on the same router.

I have a Cisco router running BGP for the main (primary) link. If my main link goes down there is a back up circuit. I have created a static route with a metric of 250. When the main link goes down the traffic goes via my backup with no problem. The problem is when the main link(primary) comes...

THe PBX is running T1. Regards, Jose'

Andy, This is T1. The way I have it configure I have channels 1-20 for data and channels 21-24 for voice. When the T1 circuit was place direct to the phone system it work with no problem. What is the IOS you are running on the router? Thanks, Jose'

Andy, The card is VWIC-2MFT-T1-DI=. I have it configure like you said but is not working. The data work but the drop and insert does not. The IOS that the 1760 is running is IP base. I then try to upgrade to IPVOXPLUS then the data did not come up. Thanks, Jose'

I have a Cisco 1760 on a point-to-point circuit. I would like to take four channels out of the T1 and connect it to the my PBX. I purchase the VWIC t1 drop and insert card and install the card on both 1760. The data came up but I cannot pass any voice on the drop channels. I have tried to...

I having problem with at 2650 connected to a T1 Frame relay circuit with 18 remotes. The serial interfaces has no CRC errors and the phone company cannot find a problem, But the sho interface shows a constant increase of output drops. What can be causing this problem. Any help will be appreciated.