Search results for query: *

Thanks, guys, I figured as much just needed to confirm. Got all these responses at the same time. LMAO about the jokes though.

I have an 8 port analogue module. I have been told by the customer that they used to do testing across two of the eight port that I had setup in a lab for them. They said that they used to get 48 volts coming across that line. I did some test on every port and I only get 34-36 volts at the...

Hi guys just so you know. I had to deinstall manager completely and then upgrade it to 5.2.29 and it came up.

I uninstalled the .net (1.1), manager and all of it's components same EAcessViolation (older version of 403 2.?) I checked the event viewer in administrative tools and it gave me the following error report: The IMS(Gateway)service depends on the IMS(Voice) service which failed to start...

TheTaker: The Manager does not open at all. kwing112000: I have not tried it on another p.c. yet but I need it up on this vvm pro remote login pc. Escorthosis: As for the DEP Solution good idea but I am running on Windows 2000, they do not offer it the same way you described it. I googled...

IP 403, I was programming some IP routes and in error selected the remote manager route of 192.168.1.99. I changed it to 192.168.0.0. This new ip was to be an update for routing to one of our other sites. Saved config. Tried to relaunch manager and it gives me an error of...

IP 403, We were pulling some cables out of office furniture and setting up as temps. Phone was working fine before, now the display reads please stand bye on display. One of the guys cut the pair of wires instead of removing them from the jack first. Customer said that the system...

Can someone verify if the following settings are used for a BCM 400 4.0 PRI. I have not set one up for the carrier recently. B8ZS, ESF, DMS 100 or is it NI1/2, Ascending order to me. Thanks

I am trying to export modules from VM Pro and the only thing I can export is the entire data base in what I do not want. Any ideas on what I should be trying? Thanks.

Hi all, Have a Polycom Soundstation 2 hanging off of an eight Port analogue mod. IP 406 vs 3.2. Making outside calls are fine. I can dial out hit Flash then 9 (to access a line) and then dial out a second time, first caller is placed on hold. Once I make contact with 2nd caller I hit...

IPGuru Thanks, I tried it out and it works great. Thanks for the explanation about the 8 getting stripped and replaced with the 9. A star your way.

Just adding your info for fututre reference with the page code. Easy to copy into file later when I've got time. Thanks

Two 406's at 3.1.65 VM Pro. Site A PRI and 1 Analogue card. Site B 2 X 4 port Analogue cards. Can anyone tell me what the short code or line build would be for access to both site's line/PRI useage? Site A dials 9 for access to the PRI right now and 8 for the analogue lines. Site B is not...

deltaserver403 Now that you are on 3.1.65 does this resolve the issue of the original question that you had with calls not being cleared after site B disconnects? Or are you still having to clear them through call status? I am going to use a similar install as yourself.

Looked into what you said. Found out that they were pushing an old copy of manager a few days old when updating there site. Thanks

I have a 406vs2 3.1.65 have a loud bell working off of a Pots Port from the 406 (Ext201). Scenario is I have Hunt Group 400 Ext 221 and 201 are in the Hunt Group. It is set to Group, ext 201 is a loud Bell that is suppoded to alter the reception when HG 400 is ringing when she is out of her...

Carrier is sending both, this was just a switch from Nortel to Avaya. As for protocol it to is correct. I am running 3.1.65. Should this be just a matter of what is sent first type of deal?

406v2 3.1.65 customer had forwarded his ext to cell phone, via a button programmed on a 5410 everything is great. Comes in shuts it off, shows up the next day phone rings sees that it is the office dialing him answers sure enough it is still forwarded from his ext. Checks his phone and the...

I have a 406v2 with a PRI on it. Right now it just displays the customer phone # when receiving a call. Does not matter if it is a direct call on a DID or if it comes through on an ext. transfer. Is this an option that can be toggled through, like on and off type of deal. I know...

TheDoz, Tech support said not to validate if you are already in a 3.1.xx to 3.1.99 and again to 3.2.17. Yet on the site it said to. Reason same as what you had mention earlier to wipe out the core software and replace it with this one. When you get in touch with tech. support ask them...