Search results for query: *

Waarschijnlijk heb je problemen met de pickup en of maintenance clutch, wat ook kan helpen is de rollen reinigen. Verder info mail naar dany_eemans@hotmail.com. Dany

Drum sensor cam positioning failure, check sensor cables and solenoide. For the sensor, try cleaning it for the solenoide try to replace it. Greetz Dany

The ink stick in a phaser 340/350/360 are the same and based on natural wax. for the 840 and 850 the wax is based on part natural and a part synthetic wax, and for the 860 and 8200 is fully synthetic wax. So it seems that the ink for an 850 is not fith for an 350. Interchange ink between...

If The buttons on your dysplay is not working, the only thing you can do is replacing the dysplay assy. Had the same problem and replaced the dysplay works fine now. Dany

Error means, the left jetstack is not heating at all or not as quickly as it should be. Only thing to do is replace printhead. Dany

where have you found this prise, in europe whe pay up to 1900 eur, about 2000$. You found is for 699$ Tell me where. Thanks in advance. Dany_Eemans@hotmail.com

this is not normal, normaly it take's about 15 to 20 min to warm up completely, depending the conditions. But 30 min can be if one of the heaters is broken like the drum heater. Concerning the error code you provide. Remove left and right cover and power up the printer, Look if you see a light...

drum heteater is slowly heating or is not heating at all. Check if the lights are going or replace drum heater. Greetz Dany

keep in mind thad a printhead will be expensive. The printhead for the phaser 8xx or 8xxx serie's is almost 1900 euro' and over 2000 $. A new printer is perhaps cheeper. greetz dany

For this cand of printer, check if you do not have accidently ink for an 850. If so the yellow becomes green, if not, yellow is not used often or the ink is burned. (to hot inside printhead). Dany

send E mail to Dany_eemans@hotmail.com and i send you the fru dissasembly list. Dany

Replace the transfix clutch, location, remove right cover just above the drum fan you find a white plastic rol. This rol is commanded by a latch. This latch assy is called transfix clutch. Greetz Dany

error means drum encoder faillure, drum has made a full revolution but sensor is not detecting. Replace drum encoder sensor. Location, remove left cover and in center of drum is the drum encoder located. sensor is the brown object. You can try to clean the inside of this sensor but be aware thad...

check the transfix clutch for operation, it can be blockt. Where to find, remove right cover on the upper side just obove the drum fan you see a white plastic rol about 4 cm. this rol is commanded by a latch, verifie his operation and clean if needed. DAny

Probably a faulty sensor in the paper prehaeter. It is likely thad the sensor ho detects the papersize (a4 or letter) is not in his socket. Meaning, the sensor is not defective but when you removed (or sombody else) the paper is can be thad the flag is not enymore on the correct position. How to...

check if intelligent mode is on and thad energy star mode is off. Whit energy star on it is like turning the printer of. Whit intelligent ready the ink in the printhead stays warm and cleaning is not nessesary, keep also in mind thad if the printer is not used or poorly used there is a cleaning...

Is your printer restarting after a while, if so let the printer go, after 3 times it give an errormessage. If not replace powersupply and or powercontrolboard. Greetz dany

Drum heater faillure, replace Drum heater and or powersupply. How to check, remove right cover and power up. When you see the drum rotating you must see a flaching light.This light is the drum heater, If you dont see replace this heater and or powersupply. Greetz Dany

Check also for worn out lift pins on the maintenance tray. If more than 2 MM replace maintenance tray. Dany

Drum maintenace cam possition error. Replace Drum maintenance clutch and Pickup clutch if one is going the other will follow shortly. Greetz Dany