Search results for query: *

Hi all I am planning to configure RAID3 for one of the realtime system we had. I am planning to have 16+1, 8+1, 32+1 LUNS. Can somebody tell me whether I can use the above configs. I am using EMC clariion CX200's. regards Srinivas Bandaru

Incase of NAS, the filesystem is being handled by the NAS head. Only the shared folder will be available to the Windows hosts. I believe windows host doesn't play any role in terms of handling the filesystem hence there is no question of max size. please clarify if windows plays any role...

Hi all, I am configuring a solution for one of my customer. The customer is going for NS600 and has a last minuite hurdle. The customer wanted to have single 3TB usable capacity and single 3TB filesystem on the nas and must given access to 6-hosts connected to the NS600. I need a...

What is the stripe element size for each LUN. Install HBAnywhere and fine tune the parameters. regards Srinivas Bandaru

May I know the the driver version, Fcode. and also let me know which switch and firmware you are using? regards Srinivas Bandaru

Hi Andyman, We were facing the same problem with our setup too some time back.We found the tapes were creating problem. Prior to the replacement of the tapes we have done all firmware upgrades, downgrades, changing cables, bridges, routers what not. We got a tool from STK support team, which...

Did you checked the drives for any read/write errors. I have utility to check these and also the utility will check for any scsi errors also. You need to have a windows machine to do this. May I have more details on the case like., host system details/scsi/fc hba's etc..., A connectivity details...

Did you checked the drives for any read/write errors. I have utility to check these and also the utility will check for any scsi errors also. You need to have a windows machine to do this. May I have more details on the case like., host system details/scsi/fc hba's etc..., A connectivity details...

I have the code. May I know why you need. Any specific problem?? regards SB

Try this out. run "scsiha -r -p -t 1" where the controller ID=1. If you any device with ID=6 NARROW, then run "ioconfig -f /hw" which should create the device file for the detected hardware. Stop "mediad" and start the same. regards Srinivas Bandaru

Thanks to everybody for their support. Finally we have achieved. We have replaced all Emulex LP982 HBA's with Qlogic QLA2340-CK. upgraded the firmware for all the qla cards and we go the good bandwidth of 100MB/s regards Srinivas Bandaru

Hi Can you send the hinv -vm. Here is my email ID: srineeb@tataelxsi.co.in regards Srinivas Bandaru

Hi, Loading the miniroot is very simple. Select 2 from the 5-menu option. regards Srinivas Bandaru

Hi, most likely problem could be the label corruption. or You have mounted the drive already. regards Srinivas Bandaru

Hi What is the SystemPartition and OSLoadPartition devices? you can find out using "printenv" from prom monitor. and also type hinv to find out how many disks available. Determine which disk you wanted to load OS and set the OSLoadPartition and SystemPartition accordingly. Example...

Hi You can follow the following procedure. Load miniroot using the Installation overlays CD. Go Admin->Shell dvhtool /dev/rdsk/dks0d4vh (the RAW device name of the CD) vd g sash sash quit quit dvhtool /dev/rdsk/dks0d1vh (the new disk raw device name) vd a sash sash quit write quit...

Hi, Connect a dump terminal or win-hyper terminal to o2 box's serial port 1 and then do everything from there. You will know what exactly happening there. Setting for term :9600/stp=1/bits=8/parity=none regards srinivas bandaru

Hi, You upgrade to FP5 but, it is neccessary to bring all media servers to the same level. Since you are in a production environment you should be extremely careful while doing this. We did this on a prod env a week back. everything went smooth. regards Srinivas Bandaru

Hi I have a Clariion 5400 with DPE and one DAE with 10 disks each. I have brocase silkworm 2800 FC switch. I have two LUNS for two systems. Suddenly one of the LUN (lun00) has gone to "UNOWNED" LUN group and is not owned by any of the SP's. I have rebooted the clariion several times...

Hi, You need to have impressario subsystems installed in the system. You have select Generic Postscript(Impressario) while installing the printer. By default you will get only Generic printer option. regars Srinivas Bandaru