Search results for query: *

Hi there, im having a wierd problem with and encore networks reciving an E1 connected to a MICS T1 card, everything seems to be working ok, calls get in and out, but we've found around 4-5 locations that for no aparent reson, they just cant call in, nobody else has this problem, just this 4-5...

Tried with a new power supply same result. The 2 ports that go to call pilot are ok, i plugged in a digital set to each one and they are fine. Any other ideas? or is call pilot dead? Thanks.

Thank you, will try that.

Yes. It just keeps sending that over and over. IF i press a key as it says it asks a few questions and starts again : CallPilot 150 Boot Loader V1.5.19 (C) 2001 Nortel Networks -------------------------------------------------------------------------- NETWORK INTERFACE PARAMETERS: IP...

Hi there, for no aparent reason call pilot stoped working, Feature 983 returns "incative feature", cant connect to it via ip, so used the serial port, and this is what i get over and over : CallPilot 150 Boot Loader V1.5.19 (C) 2001 Nortel Networks...

Is it posible on a CICS ver 7.0, for someone ( lets stay the operator ), to annonunce a call via speakerphone to an internal phone ( T7208/T7316 ) while this extension is in use with a local/external call? We've tried page, but if the phone is in use, it doesnt hear the annoucement. Thanks.

Indeed F **ADMIN did the trick! Thanks!! :)

I'll try that... thanks!

Im installing a 6x16, and im going to config menu ( **266344 ), and first of all it doesnt ask me for password ( 266344 ), it goes directly to 1.Lines, 2.Sets.. etc.. isnt supposed to go to A.Configuration, B.General Admin, etc... first? So im unable to change the date, set names for the...

hehehe just figured i posted to the wrong forum... thanks.

Im installing a 6x16, and im going to config menu ( **266344 ), and first of all it doesnt ask me for password ( 266344 ), it goes directly to 1.Lines, 2.Sets.. etc.. isnt supposed to go to A.Configuration, B.General Admin, etc... first? So im unable to change the date, set names for the...

Yeah.... IRAD was not enabled. me bad.

Nevermind, i figure it out. Thanks.

Im trying to to connect via the remote Set tool to a cics 6.0 irad, and after succefully connecting, and going into programming menu ( Feature **266344 ), i only get the software keys menu, any ideas on what could be wrong?

Im using CICS - SIP 6.1 FC Rel 01

LS/DS Cards, i've tried with 2 differentes cards ( both new ), i've also tried with a new CICS module, the only thing i haven t switched has been the software. I've also moved the whole CICS to another place, with different lines, and does the same thing.

Lines are unsupervised, as i mentioned avobe, this is not the first CICS we've installed here, this is the first one we have had this prblem with. The problem happens on all lines (4). Not indefintly on the internal station, the call returns to the operator on no answer on 6 or 4 rings (on the...

CO uses unsupervised lines, we've installed several CICS and MICS without a single problem till now. Wierd thing also if the outside call is ringing at the operator station and call is terminated, it ends it correctly, the problem only comes when you transfer the outside call to an inside...

Lines are set to unsupervised, but i have also tried setting them to supervised with same reults. Thanks

Hi there, im having a strange problem with CICS with software release version 6.1, when an outside call is received, operator picks it up, then transfers the call to an internal number, while the transfered call is ringing on the internal station, if the outside call is terminted, the internal...