Search results for query: *

Good Afternoon All. We need for an outside host to send data to an internal host thru TCP ports. I see the htcnt for the defined ACL incrementing and the log shows "%FWSM-7-302014: Teardown TCP connection" on both firewalls when using traditional one to one static NAT. But for some reason the...

Thanks for the reply PERRYPJ. I appreciate it. I'll give that a shot. Regards. Rocket.

Thanks all for your replies. Your help is appreciated. We have M3900 phones. Can this disable feature be turned off? This is driving us crazy. The same issue just happened again. This is the third time in two weeks. Random extensions stop working all of a sudden. We call the people that help...

Good Afternoon All. Hopefully someone can provide direction on this issue. I'm not a phone expert and we just inherit a Nortel Option 11 PBX at this one site. We're having a strange issue. Extensions that were working configured previously and that were working properly all of a sudden stopped...

Good Afternoon All, I'm not a phone system expert and I'm hoping someone can point me in the right direction. In one of our sites calls drop randomly and it happens in both inbound and outbound directions. Our Telco says the circuit looks clean and Avaya says it's a Layer 1 issue. I've done...

I'm glad you got it going Master. ;)

If should getting from the download folder. This is where you place your upgade files. Make sure you can browse to this folder from the subnet the phone is located at.

Since your WLAN s being seen by your laptop. I assume this SSID is being broadcast. But if it's not, broadcast the SSId to see if the phone picks it up. Check out the admin guide below. It gives a description of the phone's startup flow and some troubleshooting tips...

Does this happen only in a specific area? If it does, make sure your AP's are configured or working properly. When we had a similar issue and it was the AP configuration. You never no. Hope this helps. Rocket.

Hi Master, I'm not an Avaya expert. But I've dealt with this phones due to a project that required them. First of all, make sure you can browse the download directory and the 46xxsettings file thru IE, from the subnet where the phone is located. Make sure all required ports are open. Follow...

I'll go ahead and give it a shot. Thanks once again for all your help. Rocket.

Great Thanks North! To be honest I though it was going to be a more complicated process. But it sound pretty simple. So if I understood correclty, it's pretty much: a) Shutdown Slave. b) Unprovision Slave from the Master. c) Disconnect all StackWise Cables from both switches. d) Shutdown...

Hi All, Hope someone can help me with this one. As I've not familiarized with Cisco stack configuration I got a pair of 3750's that are currently stacked and due to some changes on the network design. They'll need to be unstacked. My question is, what would be the proper process to remove...

burtsbees/unclerico thank you for your replies. I really appreciated. Here are the answers to both your inquiries. burtsbees: Incoming traffic, which will be initiated from the outside, will be Webmail and VPN coming in thru ISP1. unclerico: Traffic that is initiated from inside going...

Hi All, Hope someone can help me with this one. We have the following network configuration: ISP1 Router ISP2 Router | | Cisco ASA 5510 Cisco PIX 506 | Cisco Switch 3560 What we are trying to accomplish is to use...

Thanks for all your tips guys. I really appreciated. We've already replaced the GBICS on both ends and it has happened again. The interface went into err-disable state. But this time around when performing the shut no shut sequenece the interface would not come up, it would show in a not...

Thanks for your reply Viper. I'll let you know how ti goes.

Hello All, I'm not a fiber expert and I'm hpoing someone can point me in the right direction. I have 1000LX fiber trunk between 2 3550 switches. This trunk link goes into err-disable state quite oftenly. The reason I get on the syslog is %PM-4-ERR_DISABLE: link-flap error detected on Gi0/1...

Hi all, I have a question on regards to an ACL. Is there any difference between the following ACL commands? permit tcp any eq www any permit tcp any any eq wwww Are they redundant commands? I see similar command throughout an ACL, but with different port assignment. I just want to know if...

Hi Guys, I appreciate all your help. Yes, all routing takes place on the L3 Switches. I'll go ahead and make the suggested changes and try it again. I'll let you know how it goes. Rocket.