Search results for query: *

puckslinger , are you allowing Windows Terminal services ? can you clarify ? L.S.

Dear network Ghost, he wants to telnet into the term server. Why did you put 3389, that is Windows Remote desktop. TCP port telnet 23. L.S.

Yes it will allow .244 to 51 only telnet. L.S.

Remove the following line: nat (inside) 1 172.20.2.0 255.255.255.0 0 0 do a: no nat (inside) 1 172.20.2.0 255.255.255.0 0 0 Since you only have 1 IP Address to the outside, then it would be: not 245 static (inside,outside) 172.20.2.244 192.168.1.51 netmask 255.255.255.255 0 0 conduit...

you don't have another interface, so you can skip 3rd: nat (inside) 1 172.20.2.0 255.255.255.0 0 0

Oh, ya, make this change. 3rd: nat (inside) 1 172.20.2.0 255.255.255.0 0 0 4th: static (inside,outside) 172.20.2.245 192.168.1.51 netmask 255.255.255.255 0 0 5th: conduit permit tcp host 172.20.2.245 eq 23 any 6th: telnet 192.168.1.51 255.255.255.255 inside

If you have only 1 public IP Address registered to your internet service, you would then want to ask for another IP Address or use the same one of the 172.20.2.244. Its up to you.

Here is the config then, try it. 1st: global (outside) 1 172.20.2.245 netmask 255.255.255.0 2nd: nat (inside) 1 192.168.1.0 255.255.255.0 0 0 3rd: nat (DMZ1) 1 172.20.2.0 255.255.255.0 0 0 4th: static (DMZ1,outside) 172.20.2.245 192.168.1.51 netmask 255.255.255.255 0 0 5th: conduit permit...

What is the ip address you want to assign to the Term server ? pick an address on the 192.168.1.x network. And you only have 1 ip address from the outside correct ? L.S.

What is your ip address for the term server, the inside and outside address ? This will make it easier. L.S.

Try this: Im assuming you aready setup your global (outside) static (DMZ1,outside) x.x.x.x(outside) x.x.x.x(DMZ address) netmask 255.255.255.255 0 0 Ideally, You want to put your term server on the DMZ. This will permit telnet to your inside network on a per host basis: conduit permit tcp...

Its pretty easy, if you are dropping packets there are a couple of basic tools you can run to verify. You can connect a PC on the same Network where the IP Phones are connected to. Then you can run some pings and trace routes to find out where on the network it is dropping packets. For the...

Faz, Does you CCNA have the latest question ? Lucio

Does this happen on all your 2924's or only one some of them ? -L.S.

The Pings are used as a Keep Alive mechanishm so the IP Office can verify if the terminals are up or down, i believe after 3 keep alives are missed via ICMP then the remote terminal will be annouced as down. The IP Phone also send ICMP request to the Media Gateway, ,same thing for the IP...

I have the same reboot problem on a 8300 Media server with a G650 Media Gateway. Some of the phones reboot during the day, any advise ?

Question, how can you tell if there will be a reboot on a phone ? Can you setup some type of firmware upgrade at a certain time ? We upgraded some of the 4610 phones from 2.1.1 to 2.2.3 Any advise.