Search results for query: *

We have a client with a KX-NS700 and one expansion cabinet with around 40 digital phones. No IP devices at all. The unit is now rebooting about 5 times a day after 7 years of working fine. I am thinking it is maybe the power supply but nothing in error log that is helpful. Where can I...

Can someone tell me how to get the caller ID info to show up in the CL button on all phones, not just the phone that answered the call? For example we have a small office where the receptionist answers a call in the file room at x105, hangs up and goes back to her phone x101 and wants to view...

Hi Guys How do I move all my connection account data from one PC to another PC so both PC's can log into the same SL2100's? Thanks Guys

Yes you can move extensions as long as enabled by the system COS by pressing SPK, dialing *2, dialing the swap password 1234 then dialing the swapped extension.

No it is the KX-DT343 or 543

Can anyone using the Emetrotel UCX with the Panasonic sets tell me if the 24 button phones can be used for CO line and or DSS keys as they would on a Panasonic PBX? We do many large residential properties and the DSS buttons are vital to call the other extensions without having to use a...

Check with SIP provider if there is a way to whitelist your WAN IP. Some providers will only accept outgoing calls from specific "allowed" IP addresses for additional security. Even though the system registered, outgoing calls not allowed.

Thanks for the response but the license card has already been replaced. Question is can I just pull the license card out of that module and put it in the new one and do a restore? I understand that the greetings and voice messages will not be carried over but the auto attendant greetings and...

Have a client that wants to replace their Partner Messaging R7 4 port voice mail due to it going into test mode several times over the past few months. My question is if you dial in and do a system backup of the Messaging module can I just pull the license card out of that module and put it in...

Thank you very much but we got it figured out.

We have a town hall and police department who's dealer went out of business and wants us to take over the system but we cannot get into mailbox 0 because it says incorrect password. Anybody have a quick way to reset the admin password as the secret backdoors we have don't seem to work either...

Hey guys I am looking for a quick and easy way to let the end user call in to their SL2100 and record a "We are closed" message due to weather here in the northeast. This was pretty easy on the Panasonic but being new to NEC I don't know best method. This message should play in front of the...

Thanks but I don't see any program for "SLT Dial Delay

We have a new SL2100 that has a 3 zone external amp hooked up to CO Line 10 and when we access the page using the code 8 XX where XX is the 2 digit zone number it takes 5 seconds or so for the audio to kick in. This does not happen from the digital sets. Obviously we have the digit 8 set to...

Not very hard to setup the 3 NS700's over gateways and doesn't cost that much. You need SIP Trunk licenses and must have a VPN between the sites. This is the way to go. We have NS700's and TDE's with gateway and once installed it is pretty solid as long as VPN stays up.

We are picking up the SL2100 after Panasonic left the business and was wondering if anyone has a cheat sheet or anything they use as a good starting point for all new installs. While I know each install is unique, there are typically things like toll restricting Vmail ports, setting system...

Yes, that's what I was afraid of. Probably best to just call out from extension of PBX to cell and then transfer to the In-Mail Pilot. Thanks for the response.

Is there a way to test the auto attendant functionality by dialing an extension number internally. Say we have all extensions within the office that have mailboxes assigned. We make a change to the DAT table Press 1 Press 2 Press 3... Now we want to test it and make sure the routing is...

Thanks for the answers and I will set up on my bench system this week to test. Just a follow up to make sure it will route correctly. From the DAT table callers selects 0 which is set to transfer to a VE 250. If we use call forward both ring to the analog x181 which is connected to the page...

Can anyone explain how to get a Virtual extension and single line extension port to ring at the same time when the virtual extension number is dialed. The client wants full time auto attendant then the dial action table digit 0 to ring a VE and ring over the page speakers at the same time...