Search results for query: *

Passwords do not have to be id + year or year + site id. Looks like the password has been changed, and at Rev 8 there is no way of finding out the passwords as all password are encrypted.

Use command asmi from the maintenace terminal, port 1. Type se to list the environment variables, type se. To change the ip address of the ethernet port se ipact= ....deletes se ipact=192.168.255.xxx ...assigns Note a reboot of the system in required for changes to take effect...

If its night bells (DANS)running off -50v , reverse the polarity at the bell and the bell should ring, which will prove your night bell is ok, if the bell does not ring check your cabling.

It looks like you can configure a C-LAN for DLG, however if you want to use CVLAN is this possible with a C-LAN ? How do you turn CVLAN on a MAPD ? DLG is only configured at the moment. Is this a chargeable from AVAYA ?

check out the FAQ there are two topics in relation to CDR Also check out thread thread690-684030

Check if system parameter CLIEX. This exception record is only output when the configurable system parameter CILEX=1. EXCEPTION records exist in order to indicate any other details that are not related to a specific call, and extra details of DASS and packet switched calls. Exception records...

Check out thread 690-738437.

Susan, Thank you for the info, it was very helpful. iSDX.

Can anyone supply a procedure for changing the data storage collection on CMS to monitor more VDN's. Do you have to go into single user mode on version 9 or above ? if so how is this achieved. How do you stop and start the data collection ? Do you, change the data storage table to monitor...

This method works. Proc Main #include "pw4menu.inc" set ftp filter local "" set ftp filter remote "" ftp local chdir "c:\program files\procomm plus\backup\" Menuselect PWMENU 18120 ;see pwmenu.ini file in the aspect directory, this selects Ascii on the toolbar pause 5 ftp remote...

You should use LCR at the originating node to route the calls to the transit node and then use the LCR at the transit node to send the call out to the public network. Add the relevant digits at the originating node to the LCR digit table (ALDT) and point them to a route list (RLDT) which in...

From what I have read when setting up IP trunking between two Avaya’s you require a C-LAN card for the signalling and a MedPro for the trunks (Bearers), thus two IP addresses are required for each node. With most other vendors only one IP address is used for a Gateway when setting up IP...

Thanks for the reply Jaymzter, good web site. Does anyone else have any idea how the calculation is done, I have run trunk analyser from ASA and need to be able to explain the figures, which I presented in a quaterly report.

Use the LEX command to list the attributes associated of each telephone that is required to be a member of the pick-up group. If the extension is a member of an existing group the lex command will display the PG refno. i.e EN2261 EC061713 CS08 TA12 MOH 000 MEMBER PG 020 Use the "LPG A" command...

6.1 does support flexible slots. However if your analogue extension slots are double slots, i.e codec/extension cards these slots are fixed in software and cannot be revised or added, a reconfig is required. 6 slot trunk group are also fixed in software. RSLT: XXYY/PART: Physical address of a...

Can anyone tell me how the trunk analyser report is calculating the values for, “Needed Trunks” and “Recommendation” in relation to the values given in the report. Is there any documentation on how ASA runs and calculates the values in the report?

Thanks Jaymzter.

Has anyone got a cheat sheet for setting up annoucements on a G700.Any other information on G700's would be appreciated.

Qsig on the iSDX does not support TEXT display. You should look at using DPNSS as QSIG only offers the same features as Q931 (ISDN). CLI is supported.

The first thing to check is system parameter SPEKO. Type of keysystem working supported. (Range 0 to 2, 0 = basic keysystem working - default, 1 = enhanced keysystem working, 2 = networked keysystem working) To set up a local keysytem group so that group members can be monitored is as follows...