Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. thequietstorm

    Setting up Netscreen Firewall

    Someone please help me. I have a Netscreen firewall connected to my cable modem and I would like to restrict users on my network from going out any websites except the one I permitted. How can I set it up? I have very little experience with Netscreen. Right now, I have the cable modem...
  2. thequietstorm

    Bridging Two Cisco 2950 Switches

    I need to verify the 2950 configurations, is there another way to access it, since I can't ping or telnet into it? I have an analog line and a 56k modem onsite? Do you think I would be able to dial up into it? I know that's possible for a router? Any ideas, I am desperate.
  3. thequietstorm

    Bridging Two Cisco 2950 Switches

    This switch is off site. Since I can't reach I can only try to work with switch one. I thought may be I could make some changes to the port config in switch one that connect to switch two and bring it up that way. By the way, both switches are in the same subnet and vlan.
  4. thequietstorm

    Bridging Two Cisco 2950 Switches

    I have two Cisco 2950 switches. I connected them with a cross over cable and assigned each of them an IP address. I call them switch one & two. Now from switch one I can ping all thee nodes attaches to switch two, but I can't ping switch two? Am I missing something in my config? Everyting...
  5. thequietstorm

    Help with HSRP

    Hi everyone, I need some assistance configuring a couple of routers. The routers will be in a small office network which link to our remote office via frame relay and ISDN dial backup. I want to set up HSRP on these router, but I am so sure how to start. Can someone please help me? Any...
  6. thequietstorm

    Set up dialer in XP

    Hi everyone, I am have an XP machine at home with a cable modem connect to it. Sometime when I am away from home I would like to connect to that machine and share the network connection. Is there a way to do that? I was thinking about using a dial up line to connect to my home pc and share...
  7. thequietstorm

    Configure a dialer

    Hi Everyone, Can someone help me configure the dialer for a router. I need to be able to dial into it, in case I need to make changes. Anyone has a sample configuration or some instructions on how to do this task? Thank you in advance for you help.
  8. thequietstorm

    Configure a cisco router with 2 ethernet interfaces

    Thank you everyone for the help, Yes Wybnormal both routers goes to the same place on the WAN. I have two 2611 routers and two enterasys switches. I am putting one connection from each switch to the routers in case one switch fail. I want the router to switch to the working switch. Each...
  9. thequietstorm

    Configure a cisco router with 2 ethernet interfaces

    Hello everyone, I need some help configuring a router. I have a router with 2 ethernet interfaces, each ethernet interface will be attached to a switch, for redundency purposes. So now the question is: Do I configure both interfaces to be active at same time? Or Will the other one...
  10. thequietstorm

    Router

    Can someone please help me? I need to buy a couple routers for a small office. I would like something that would give the capability of Voice of IP and all those other cool features. Anyone has any suggestions? I was looking at the cisco 2691xm, but so far I have been looking at anything...
  11. thequietstorm

    Frame Relay, ISDN and DS3

    Thank you wybnormal that was very useful. As you probably noticed, I am kind of new to networking. Currently I have a very small project I am working on. I need to setup a network for a small remote office. it's for about 15 users. There will be a lot of file sharing, so therefore bandwidth...
  12. thequietstorm

    Frame Relay, ISDN and DS3

    Can someone explain me the different/advantages between frame relay, ISDN and DS3. Which one of these technologies would be the most economical and provide more bandwidth for a remote office of 15 users who will be doing a lot of file sharing? I am planning on installing 2 routers the primary...
  13. thequietstorm

    Building a small office network

    Yes, the frame relay circuit is connecting to a remote office. I want to use to routers for redundency. By the way, can you give me some insight of HSRP? Do you think using an ISDN line as a backup link is a good idea? Is there better alternative. My users are going to use a lot of...
  14. thequietstorm

    Building a small office network

    Hi Everyone, I need some help. I want to build a small office network for about 6 to 12 users. This network will be use for file sharing, e-mail and etc. I am thinking about buying a couple cisco routers and a switch. Anyone have any suggestion on a design plan. One router will be connect...

Part and Inventory Search

Back
Top