Search results for query: *

Hi, ... could anyone tell me please, how I can figure out the size of the Port Buffer on modules??? Is there a command, or maybe a link would help as well.n I couldn´t find help at the Cisco site. I have following Modules: 5225 R for a Cat 5000 4248 for a Cat 4000 Thank you best regards ypswes

Hi to all my question: I have a Cat 5000 with a sup III, and mls is enabled by default. BUT I don´t have a RSM installed. When it´s enabled I get "MLS - Too many moves" messages, probably because of a lot traffic with two gig links . So I simply disabled the mls, and the messages...

I would check it with show ip arp [mac] ( looks like this ffff.ffff.ffff.ffff) best regards ypswes

Hi, .. in the next time I have to change a supII (cat 5000) into a supIII, because of Gigabit , Multicast ect. advantages. Whatever, the supII now is in VTP server mode, and the directly devices attached to it are in transparent mode. (I know there are also clients, ... but right now I dont´t...

Thank You, I think I´ll try to configure the trunk in vlan 1 , and then add slowly all the others Vlan ´s ... we´re not supposed to use flow control, ... --- keep it stupid simple---- exactly what you ´ve said. best regards ypswes

I agree, ... especially the auto mode with Etherchannel, because you can´t go back to the off-mode, without interrupting the connection for a sec. And, .... autonegotiation ... and ...so on. But ---as far as I know it should never work when both ends are on auto ??? best regards ypswes

Hi Jeff well, ... thanks for explainingthe error messages. O.k., I´ll try it the next time we have the posibillity to disconnect the CampusCore Switch ;-) Hmmm, could you please say one or to more words to your experience with flow control and udld. best regards ypswes

Thank you for your help,I´ll check it out, especially the VLAN 1 configured ONLY on the Trunk ports, and then bring it up step by step. One more question to Flow Control: Do I need to configure Flow Control, as far as I know I haven´t seen this on our Campus Network, and we have some more GIGA...

Hey ... during the Installation and Connection of two CAT 5500 with a Gigabit Trunk the following errors ( and a nice Loop ) occurred: %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(40000000) %SPANTREE-2-RX_1QPVIDERR: Rcved pvid_inc BPDU on 1Q port .. %SPANTREE-2-RX_BLKPORTPVID...

Hey ... during the Installation of two CAT 5500 with a Gigabit Trunk the following errors ( and a nice Loop ) occurred: %MLS-4-MOVEOVERFLOW:Too many moves, stop MLS for 5 sec(40000000) %SPANTREE-2-RX_1QPVIDERR: Rcved pvid_inc BPDU on 1Q port .. %SPANTREE-2-RX_BLKPORTPVID: Block ... on...

There is no workaround: Cisco says: Important Notes For Catalyst 2900XL/3500XL/2950 Switches: Catalyst 2950 series switches only support 802.1q trunking. They do not support ISL trunking. Currently, Catalyst 2900XL/3500XL switches do not support Dynamic Trunking Protocol (DTP). Thus, it is...

Hy I have a Cisco 7000 with 4 MB Flash, and an image for an rsp. But I have only one rp and one sp, so I´d say it´s the wrong image. RRRRRRRRR For sure I´cant initialize the Router properly, ... so finally I´m stuck in the boot strap modus. There is not even a rommon>, I simply see a >. I can...

Check this out: http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/12cgcr/fun_c/fcprt2/fcaddfun.htm#xtocid160213