Search results for query: *

Hi, I am using Incredible pbx 13.12 and it's configured with D410P voip card. we have configured one dahdi trunk(g0) for all the 4spans, now we need to configure separate dahdi trunk for each span. Can any one advise how to configure dahdi trunk. dahdi-channels.conf ; Span 1: TE4/0/1 "T4XXP...

Hi, Thanks for your reply, I will try and get back you shortly, Regards, Balamurugan. P

Hi, I am using incredible PBX 13, and one of the asteriskcdrdb file cel.MYD size is keeping on inreasing, how to reduce the file size. Regards, Balamurugan. P

Hi, I have DM/V1200A_4E1 cards and installed on windows 2003 sever ( HP DL 380g3), and the system detects all the cards. I have installed the dialogic software Intel system Release 6.0 PCI. After installing the required software the DCM could not detect any cards. Can any one help me out to...

HI, I am trying to configure MedPro card TN 2302 in my PBX G3si. After configure the MedPro card am getting the following result. test board 01b16 TEST RESULTS Port Maintenance Name Alt. Name Test No. Result Error Code 01B16...

Expecting any technical tips to fix this issue

Expecting any technical tips to fix this issue

If I changed the switch settings to 10M/half & 10M/full the Red light is on, and if its in 100M/full the link and & 100bT lights are on & red goes off and the port on the network switch is down. what could be the issue.

Please find the below details of my PBX isplay capacity Page 10 of 10 SYSTEM CAPACITY CURRENT SYSTEM INFORMATION Software Load: R009i.05.1.122.4 Memory Configuration: G3siV9 Offer...

i have only one MedPro card. The MedPro card adapter has 9pin serial and RJ 45, whats the use of the serial pin. Can you please. Thanks, Bala

I have tried that, when i changed the c-lan adapter to medpro the link & 100bt lights goes off and red (alarm) is comes on. C-lan is down when connected with medpro adapter.

Thanks bsh. When i connected the medpro to my switch then only the Link and 100bt lights are in green but at the same time on the switch the port is down. Is there any connectivity issue and i am using the 50 pin connector and following pin details for RJ 45 . RJ45 RJ45 568B Lead 25...

I can ping 01b17 (10.101.2.22) from my switch (10.101.2.251) but couldn't ping 01b16 (medpro 10.101.2.33). I have connected 01b16 & 01b17 to network switch through straight cable. Board 01a04 for Avaya Site Administraton. My PBX Version is...

Can any one help me out to fix this issue...still am struggling test board 01b16 TEST RESULTS Port Maintenance Name Alt. Name Test No. Result Error Code 01B16 IPMEDPRO 52 PASS 01B16 IPMEDPRO...

That I have changed to 1 hange ip-interfaces Page 1 of 6 IP INTERFACES Enable Net Eth Pt Type Slot Code Sfx Node Name Subnet Mask...

Its connected with cisco switch with 100mbs/full duplex. Both C-lan and MedPro connected on the same switch.

Thanks for your swift response. The link lights are in green but no action on TRMT and RCV and i have connected with correct adopter

Hi, I have G3 Si PBX and am trying to configure MedPro card TN 2302 in that. I have assigned ip address for both C-LAn and Medpro card and am able to ping C-Lan ip from the CM as well my cisco switch but am unable ping ping MedPro IP from CM & switch. Can any one help me to fix this issue and...