Search results for query: *

I have a master that I clone and swap in every R6 BCM50 we get in (true R6 units, not upgraded) and have never had any issues. www.number1telecom.com

That's what I would like some for is to be able to add RAID. Also from time to time when we purchase these out of service they are missing the hard drive and tray. People take out the hard drive and I'm sure throw the whole drive & caddy in the garbage as "security precautions" as if we would...

I am looking for additional BCM 450 hard drive caddy units. The actual metal tray that the hard drive mounts into before sliding into the BFT. Does anyone know a place where these can be purchased or a brand / part # for a good replacement? I noticed the ones I have do have a part # on them...

Found some that will work.. The "head" portion is a tiny bit shorter than the original ones but they still work. Here are the specs: 3/16" Hex Head Standoff Steel Zinc Finish 4-40 x 3/16" Thread Length 3/16 Head Length Male-Female www.number1telecom.com

This may be a strange request but I am curious if anyone knows the specs on the standoff screws on the BCM media bay modules with amphenol connectors. A lot of times we get the modules in with these screws removed and would like to replace them. Tried buying some "M3 8mm+6mm" but the thread is...

I understand but what I’m saying is I don’t know if I’ve done everything. There’s some steps that aren’t completely clear and if someone is able to provide me with the details, then I’d like to give them a try. I don’t think the expansion is seeing the main unit because I’m not putting the...

All of the units were flashing green yesterday until I hooked them up to the 7.0 and they flickered for a while presumably a firmware “upgrade” and ultimately went red which is where they stand now. 4 of them doing the same exact thing again why I don’t think it’s a hardware issue. Just looking...

@intrigrant.. You are the one who originally posted the step by step instructions I am following so hoping you can give a little more assistance than trash these. What do the TFTP, HTTP, PC IP, & Phone File Server Type need to be set at? Do you see anything else that I could possibly be...

Okay. So what do I need to do? www.number1telecom.com

Okay.. What should those settings be? Should I have the TFTP & HTTP server IP set to the address of the 500v2 or of my PC? And PC IP set to my PC that has manager I assume? Phone File Server Type Custom or Memory Card, HTTP Redirection Off or Phone Binaries? Also.. Should Security TFTP...

I still don't see the DS30B in manager. Here's what I've done: - Create an offline config.. System in Standard mode, Combo card slot 1, DS30B expansion 1 - Load configuration to system - Reload Essential License - Save, Reboot and power down - Connect DS30B to expansion port 1 on IP500v2 -...

It is not a brand new unit.. It is a decommissioned unit from a company that went out of business. We actually received a few of them and they're all doing the same thing and that's why I believe it be something I'm missing on my end and not a faulty unit/units. We goofed and forgot the DS30B...

I have a Digital Station 30B module I am trying to get going and it just has a solid red light System is a IP 500 V2 R9.0 I have read up quite a bit on this and feel like I've tried everything. I did everything in this thread step by step (can't even tell you how many times)...

Only 1 clock card and 1 PRI are needed. www.number1telecom.com

Make sure you have licenses for the additional station port. www.number1telecom.com

Keycodes and programming should not change during the upgrade. I don't recall if the language copies over as well. www.number1telecom.com

In short.. It's English/Cantonese (which I believe they speak in Hong Kong). www.number1telecom.com

The $30 ones on eBay include activation. States it in the listing. www.number1telecom.com

Could be the 0x16 module going bad. I'd try swapping phones around as curly stated and see if the problem persists on the ports or on the phones. www.number1telecom.com

Power down the unit. Leave the 2.0 in and install the 3.1 card in the top slot above it and power it up (while connect to a system) and let it do it's thing. The lights will flash for a while and when the eventually go completely blank, it means it's complete. If you happen to leave it past the...