Search results for query: *

it is loopstart and supn YES. But the line is only stucking at 2250. If it goes to any digital/analog extension, it disconnects after Hang up. Also without callpilot it disconnects also from 2250. It only does when Callpilot is active

Hi All, I have a system release 4.00 and all patches activated. We have installed callpilot for welcome anouncement. Here is the problem, When we call via CO trunk and press 0 for attendant, it came to attendant. When caller cancel the call, 2250 console keeps ringing till answer and...

You can try Algo or Nice recording

Check the crossconnect cable between CPU`s.

Insert new RMD (Compact Flash card to the CPPIV) and back it up again

Hi All, Does anyone installed the Release 7.50 Linux software on a virtual machine? What is the requirements? Does it works well? What is the limits? Thanks in advance for replies.

hI All, I have a CS1K rls 7.5 and Avaya ACM connected via PRI E1 trunk. DID trunks terminated at CS1K and when call comes in I can see the caller id at Nortel phone. However when I transfer the call to ACM it shows the extension number of CS1K instead of Originated Caller ID. If I forward call...

Hi We have NICE Recording R6.6 PL10 and AVAYA ACM. we are using SoftAttendant which is ONEX Attendant. Nice is recording the call. However there is no CLIP COLP information of the call. Is anybody having this issue? Best Regards

https://res.cloudinary.com/engineering-com/raw/upload/v1551368684/tips/node1_pzviqv.cfg https://res.cloudinary.com/engineering-com/raw/upload/v1551368694/tips/node_jmqryl.pch https://res.cloudinary.com/engineering-com/raw/upload/v1551368712/tips/node1_nmq1t5.ctp...

https://res.cloudinary.com/engineering-com/raw/upload/v1551361153/tips/node1_rjwphr

yes we do. When I install the system I ve entered the keycode and it is accepted. Also Signaling server and nodes doesnt have anything to do with IP license as I know

Hi Tbonz25 I did softreset from elenmen manager and hard reset from the cabinet. Technically call server receives the NODE ID. But it only stays in the pdt. When I do "STAT SS", "STAT LINK NODE 1" system gives nothing. I assume call server receives it but doeesnt activate it.

I did everything. Node file is on pdt valid Element manager Node configuration is OK. When i DO >LD 117 STAT SERV THERE IS NO SERVER AND NODE. But the node file in Pdt is valid. I have no any other idea. Any help wold be appreciated

Thanks for your help. I will do the last step. I will delete the node file from C/u/db than will delete the node from Element manager. Than I will reboot all system. I will create another node in the element manager. I will post ASAP

here is what I am getting SRPT170 pbxLinkMon: pbxLinkParsePCHFile stat() c:/u/db/node/node.pch file got wrong valu e, errno = 0x380003. SRPT170 pbxLinkMon: pbxLinkParseNodeFileByDir no nodeXXXX.cfg file was found. AUD000 SRPT170 pbxLinkMon: pbxLinkParsePCHFile stat() c:/u/db/node/node.pch...

SRPT170 pbxLinkMon: pbxLinkParsePCHFile stat() c:/u/db/node/node.pch file got wrong valu e, errno = 0x380003.

I did the fresh Software installation from scratch and Tyepd yes for a signaling server. What I saw might be difference, When I read the NODE1000.CFG file it says IPL 4.0 and I couldnt see the Node IP. I have only seen the IP address of SigServ and MC32 cards.

I have checked the node file in PDt c:/u/db/node and all of them are there. and I have cheked if the file updates when I transfer the node. But when I do STAT LINK NODE 1000 ıt says no node found

LD 117 >> STAT SERV NO SERVER FOUND