Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. KodiakAK

    copy and pasting config

    I am trying to mirror an existing up and running netscreen onto a lab environment netscreen in order to work on getting tunnels up and running. Is it possible to cut and paste the encrypted VPN preshare key? for example, I can cut and paste a cisco hash into a new config and it preserves the...
  2. KodiakAK

    cant enable crypto isakmp

    Thanks. I was able to procure it legally without incurring any charges.
  3. KodiakAK

    cant enable crypto isakmp

    advanced security IOS. I assume this is something you have to pay cisco a million dollars for?
  4. KodiakAK

    cant enable crypto isakmp

    this is all I get.. what gives? Router(config)#cry Router(config)#crypto ? ca Certification authority engine Enter a crypto engine configurable menu key Long term key operations pki Public Key components provisioning Secure Device Provisioning...
  5. KodiakAK

    new me3400, cant ping vlan ip address

    Changed e0/24 to port-type nni and could ping it with ethernet configured in the subnet range, and still browse the internet with a ppp session on a different network.
  6. KodiakAK

    new me3400, cant ping vlan ip address

    what I can do is plug a synced up DSL modem into port 24, and my laptop into port 1. the laptop is provisioned as 10.137.32.146 255.255.255.240. I can authenticate a PPPOE session from my laptop to the internet and browse, but I cant ping my switch. The end goal here is to serve some...
  7. KodiakAK

    new me3400, cant ping vlan ip address

    When I configure my laptop to 10.137.32.146 and plug into int fa0/1, why can I communicate to whatever is plugged into 0/24, but cant ping the vlan ip address of .157? vlan 999 uni-vlan community name Management_VLAN ! ! ! interface FastEthernet0/1 description ADTRAN...
  8. KodiakAK

    IPv6 config

    for the next noob that comes around, I discovered: autoconfigure takes fe80 and adds it to the front of the mac address of the NIC (plus some filler in the mac address part) if you get assigned a block of addresses, they get pasted on where fe80 goes and it becomes globally unique...
  9. KodiakAK

    IPv6 config

    I have some IPv6 addresses I can use to get out to the internet, and I am trying to configure routing between two interfaces on a cisco 1841. interface FastEthernet0/1/0 description IPV6 TEST PORT no ip address ip nat inside ip virtual-reassembly duplex auto speed auto ipv6 address...
  10. KodiakAK

    T1 link (ppp?) between router and Dslam

    Transmission engineer says t1 ports are for TNE modems and I will never be able to uplink to them, even though the documentation says uplink ports.
  11. KodiakAK

    T1 link (ppp?) between router and Dslam

    show int desc says multilink is down. I guess the far end would have to be configured for multilink too, which isnt possible on this equipment. I wonder if it speaks HDLC?
  12. KodiakAK

    T1 link (ppp?) between router and Dslam

    here are the relevant portions of the config controller T1 0/0/0 cablelength long 0db channel-group 0 timeslots 1-24 ! controller T1 0/0/1 cablelength long 0db channel-group 0 timeslots 1-24 ! ! ! ! interface Multilink1 ip address 192.168.254.193 255.255.255.192 no ip redirects no ip...
  13. KodiakAK

    T1 link (ppp?) between router and Dslam

    I am working on a lab environment where I want to connect a router to a zhone Dslam through a t1 link. is ppp the correct encapsulation, or should I use Frame relay? When I bring up the t1 controllers, it wont activate the serial interface unless I issue the channel-group x timeslots 1-24...
  14. KodiakAK

    LAB trying to turn up FXO FXS

    OK, I went through my stack of old gear and found one with a Packet Voice DSP Module. I put an FXO in slot 0 and an FXS in slot 1, show run and boot-start-marker boot-end-marker ! ! no aaa new-model voice-card 0 ! voice-card 1 ! ip cef very excited. The first thing I would like to do...
  15. KodiakAK

    LAB trying to turn up FXO FXS

    I have 2 1760s with [2] vic 2FXO cards in one and [2] vicFXS cards in the other. How do I enable the cards so I can see them in show run?
  16. KodiakAK

    Any tips on upgrading to mcd 4.0?

    Thanks, just got it going. After migrating, I used the existing ARID, and upgraded to 4.2. I set mytai/tapi to yes and networking to yes in the licensing and options form. Everything seems to be running smoothly.
  17. KodiakAK

    Any tips on upgrading to mcd 4.0?

    Does that migrate the DB?
  18. KodiakAK

    Any tips on upgrading to mcd 4.0?

    Software assurance is active so I will try to use existing. I don't know how to migrate the DB though.
  19. KodiakAK

    Any tips on upgrading to mcd 4.0?

    Thanks I have read through it and have a few more questions. I see the command to do a database check before migrating the database, but I am not clear on how to actually migrate the database. Will it be a part of the upgrade software that will occur as I am running the upgrade software...
  20. KodiakAK

    Any tips on upgrading to mcd 4.0?

    The upgrade to 4.0 went very nicely. thanks. where can I find something to read about the rest of the process?

Part and Inventory Search

Back
Top