Search results for query: *

Thank you Splic3d, I checked the card and it has a single daughter board on it. https://www.dropbox.com/s/hpl12zym6obpb8l/2013-02-25%2011.09.09.jpg Could i add another single daughter board to this? What would i need?

I'll be the first to admit that i'm a noob when it comes to Nortel. I don't even really know what the proper name for the equipment we've inherited so I've attached photos to better relay what i'm trying to do. In our current building we have two cabinets connected with an SCP card in cab1 and...

I have 4 trunks that i can dial out from, but how do i add incoming calls to them to route back to my call pilot? If i call then it just rings to no where (apparently) They are all on card 15 units 0-3

Thanks. I was tempted to remove the mini IDE hardrive and hack the SAM database but luckly someone found some old notes with the pw written on it.

Our system hasn't been touched since it was installed and no one can find the administrator passwords. I can login to the cpanel but not the actual desktop. I need to change the ip address of the C-LAN. This is on an appliance card with no cd drive or usb to boot my password hack tools...

I'm trying diagnose a separate issue but would like to place a test call over individual trunks. I'm not sure what the current outgoing routes are and I'd like to review those as well. Is there a way to do this and to retrieve this information?

Thanks. That FAQ (http://www.tek-tips.com/faqs.cfm?fid=4654) did provide some more information. I learned that the KEY assignment was where the CLID was being chosen but all of my phones are set for 0 and the CLID 0 does use DIDN=YES KEY 00 SCR 5616 0 MARP CPND NAME...

Thanks Buddy, your assistance has been very helpful. Here are the outputs from those commands.. TYPE NET_DATA CUST 00 OPT RTA AC1 INTL NPA SPN NXX LOC AC2 FNP YES ISDN YES VPNI 1 PNI 1 PINX_DN MBG 0 BSGC 65535 PFX1 PFX2 HLOC LSC RCNT 5 PSTN NO TNDM 15 PCMC 15 SATD 1...

Thanks! Is there a way to view (PRT) the current NET_DATA settingss?

I'd like to find out how to change the outgoing caller ID number sent from each station. Currently anyone calling from our PRI get our main billing number so anyone returning calls just call back to the main switchboard. I'd like this to either: 1) show the actuall DID of the caller or 2)...

wow.. your right. it actually did remove it. thanks.

I'm trying to remove an analog station LD 20 REQ: OUT TYPE: 500 TN 7 2 and i'm getting returned: HUNT DN 5699 5699 is our voicemail hunt. PRT: HNT HTNO 5699 does show this TN listed here. I'm just not sure how to remove it so i can remove the station.

Our telco provided POTS backup lines to our PRI. If the pri was unreachable or busy, any call to any DID would be routed to a bank of POTS lines. We also had the ability to do remote call forwarding to the main hunt number of those backup lines to forward to an offsite location if necessary...

I have a few 3904's that are not booting up. They just display an icon of a phoneset that is crossed out. (see photo) The error seams ominous. I replaced the sets and the line came up fine, but now i have a box full of phones that I'd like to get working again. Any help would be appreciated.

Thanks KCFLHRC, I ran those commands but it returned SCH0443 "that list does not exist" Could that mean i don't have any group hunting? I know i have several hunt groups, i tried using the Dn's of the groups to see the members but it returned the same error

in LD 20 i'm trying to print all list with GHT but getting error SCH0703 and SCH0443 REQ PRT TYPE: TYPE GHT LSNO SCH0703 RNGE SCH0443

I'm trying to setup an extension to forward calls to an outside number if the extension is not answered. I probably went the long way of doing this but.. -I created a new RPL permitting the outside number to be dialed -created a new class with the revert DN set to use the new RPL -set the...