Search results for query: *

I have pix 515 ver 6.2(1) and I need to erase the startup-config. How do I do that? I issue a clear configure and write erase memory but my startup-config still remains the same. btw does the pix have NVRAM too. It seems like the IOS and startup-config is stored in flash base on the book I'm...

Thanks very much m4ilm4n.

ok maybe there is not interface mode but what will this command do? pixfirewall(config)#interface ethernet0 the result should be pixfirewall(config-if)# my pix return this pixfirewall(config)# which keep me in configuration mode? how do you config an IP address for pix?

from configuration mode how do you enter interface mode then?

I starting to learn about Pix Firewall & I have some issue with it that I need some advice. My Pix is version 6.1(1) The issue that I am having is that when I'm trying to type interface ethernet0 it still put me in global configuration mode. I could never get me into the interface configuration...

I'm new to openSuse and I need some app to connect to cisco router though the console port. I installed me Putty but I'm unable to connect to it. the error message I get is unable to open connection to: unable to open serial port my serial line setting is /dev/ttyS0

I'm confuse about CIDR; can you give some example.

Is CIDR & Route Summarization the same thing?

Nope it still not work but I need you to answer one question. Ok correct me if I'm wrong. All switch ports by default belong to the DEFAULT VLAN which is also know as the NATIVE VLAN. Now once you create VLAN 20; you now have 2 VLAN in the switch. You decided to assigns some ports to VLAN 20...

It works on my packet tracer but on live router it won't work. Well I will update if I found anything wrong with it.

host 172.17.99.10 default gateway is 172.17.99.1 I did the no ip routing and assign default-gateway too ok it seems that vlan 20 and 1 can communicate but vlan 99 can't. I also want to mention that the native vlan for the trunk is vlan 99 and in this switch I have one switch belong to vlan 99...

Thanks for the clarification.

I have a router to route between VLAN and I assume the Management is just another VLAN. Here my physical topology. Ok since I don't have 3 or 4 PC I turn the router into a PC. These 2 router are in VLAN 20 and their ethernet interface are configure like this. inter e0/0 ip address 172.17.20.3...

Can you put some host in the management vlan and ping the regular Vlan host. I try this but I cannot ping them.

Ok is it safe to say that there are 2 type of loop avoidance for layer 2 switch. They are STP & RSTP: STP can use PVST or PVST+ to prevent loop RSTP on the other hand can use PVST+ OR Rapid PVST+ Am I right? Any input would is appreciated.

I configure the vtp domain and password and it works.

My question is how come the trunk is not establish? SwitchA config interface FastEthernet0/1 switchport trunk encapsulation dot1q switchport mode trunk A#sh vtp status VTP Version : 2 Configuration Revision : 1 Maximum VLANs supported locally : 68 Number of...

@unclerico So I use live router and it doesn't work but it work in my packet tracer @brianinms no

So I got two router connected and all communication is working and I'm using RIP. Now I have router A and B and I want router B to propagate a static route so I issue this in router B ip route 192.168.1.0 255.255.255.0 loop3 router rip redistribute static When I check router A routing table I...

when entering the command sh ver lots of info. appear but I'm confuse with this one. with 60416K/5120K bytes of memory. The sum of these numbers is 65,536K, or 64 megabytes (MB) of total DRAM. my question is how can kilo = meg?