Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. mlgmartin

    Is J9151A 10G Tranceiver compatible with HP3500 J9310A switch?

    Dear HP Gurus! Before buying these expensive transceivers (J9151A) we made sure that it is compatible to our HP3500 switches (J9310A). According to HP documentations, yes it is compatible! However, when we plugged the transceivers to our switches, the log said it is incompatible. We were...
  2. mlgmartin

    What is better, SIP Trunk or E1 ISDN PRI?

    Nowadays, ISPs/Telco are now offering SIP Trunks as an alternative to E1 ISDN PRI for VoIP Phone System deployment. Do you have any experience using SIP Trunks from the ISP/Telco? Is it easier to manage than E1 ISDN PRI? Is it cheaper? Would you recommend it? "It is an equal failing to trust...
  3. mlgmartin

    How to prevent trunk to trunk lockout?

    Greetings to all NEC Gurus! I used Quintum analog gateway to link my NEC PBX with my VoIP Phone System. My problem is, the NEC PBX who do the trunk to trunk connection doesn't release after ending the call. Is there a parameter that I missed or this is normal to analog phone system? Is there a...
  4. mlgmartin

    How to enable trunk to trunk transfer from NEAX 7400 to VoIP System?

    NEAX 7400 ICS 140MX "It is an equal failing to trust everybody, and to trust nobody.
  5. mlgmartin

    How to enable trunk to trunk transfer from NEAX 7400 to VoIP System?

    Dear Telephony Gurus, I'm not expert in NEC PBX maybe someone out there could help us. We are in a middle of migration from analog phone to VoIP phone. We are currently running the 2 systems in parallel. We are using Quintum AXM2400 (FXO/FXS) as a gateway between the two systems. We would like...
  6. mlgmartin

    Quintum DX and AX Series Firmware

    Is the firmware of Quintum DX and AX series the same? "It is an equal failing to trust everybody, and to trust nobody.
  7. mlgmartin

    Quintum DX3000 E1 ISDN PRI Voice Gateway

    Thank you for all your comments. "It is an equal failing to trust everybody, and to trust nobody.
  8. mlgmartin

    Quintum DX3000 E1 ISDN PRI Voice Gateway

    Our provider told us that Quintum DX3000 E1 ISDN PRI Voice Gateway can not be administered through Quintum Tenor Configuration Manager. Configurations can only be done through CLI. Anyone who can confirm this? "It is an equal failing to trust everybody, and to trust nobody.
  9. mlgmartin

    How to expand Dell PowerVault MD3220 using MD1220?

    Dear Dell Gurus, Currently we have Dell PowerVault MD3220 with 1 Diskgroup and 3 virtual disks. Now we need to expand our storage by installing 1 MD1220. Our goal is to increase the size of the virtual disks. After connecting MD1220, we saw 12 TB unconfigured space. We tried to increase the...
  10. mlgmartin

    Call forwarding issue on NEC NEAX 7400 ICS

    Dear NEC Gurus, Is it by design that the system check the restriction of the caller (extension) before forwarding the call? I have this situation: Phone A - No dial 9 Phone B - Dial 9 capable Phone C - Dial 9 capable (forwarded to 9 + External Number) 1. If Phone A calls Phone C, Phone A...
  11. mlgmartin

    How to change authorization code behavior on NEC NEAX 7400 ICS?

    Dear NEC Gurus, Is it by design that you need to access a 2-digit code first (i.e. 88) then dial the authorization code then finally dial 9 + telephone number? How can I configure my system so that the caller will dial 9 + telephone number first then at the end he can dial his authorization...
  12. mlgmartin

    How Can I Restrict the Authorization Code from Accessing Special Trunk Route

    Dear Friends, Initially, when we configured our Authorization Code, we set it as Unrestricted (can dial all the trunk access codes). Now, we need to restrict the authorization code from accessing our GSM Voice Gateway. Do yo have any idea where should I start? "It is an equal failing to trust...
  13. mlgmartin

    How to enable web interface on Cisco 1941 Router?

    I have already tried this one with no good result. ip http server ip http access-class 23 ip http authentication local ip http secure-server ip http timeout-policy idle 60 life 86400 requests 10000 I have GE0/0 (WAN) and GE0/1 (LAN). My Management PC is connected on GE0/1 via cross cable with...
  14. mlgmartin

    HP Command Show Mac-Address

    Is there a way to log all mac-addresses with their corresponding port number? I want to trace a user but I need him to log-in in order to see his mac-address using the command show mac-address. If this is not possible, is there a free windows application that could do this? "It is an equal...
  15. mlgmartin

    What is the difference between the following 4 Products?

    HP E3500-48G-PoE+ yl Switch J9311A HP E3500-48G-PoE yl Switch J8693A HP E3500-48-PoE Switch J9473A HP E3500-48 Switch J9472A "It is an equal failing to trust everybody, and to trust nobody.
  16. mlgmartin

    What is the maximum number of NICs that can be teamed?

    What is the maximum number of NICs that can be teamed on Windows Server 2008 R2? Should we consider the switch limitation for LACP like most of the HP Procurve switches that only support 4? "It is an equal failing to trust everybody, and to trust nobody.
  17. mlgmartin

    Nortell how to know if i have an available analog extention

    Try to look for a TNs that were programmed but no telephones connected into it. For analog, there's no other way but to physically inspect your panel. For digital, you can use a command to disable all TNs without phones connected. "It is an equal failing to trust everybody, and to trust nobody.
  18. mlgmartin

    Reprogramming an ACD Queue - I'm Missing Something.

    Why not put directly the telephone number in the NCFW of ACDN 1145? "It is an equal failing to trust everybody, and to trust nobody.
  19. mlgmartin

    LACP Trunking and Network Teaming

    I'm using Broadcom Advanced Control Suite 3 (BACS3) on a Windows Server 2008 R2. The network teaming wizard provided 3 option as follows: 1) Smart Load Balancing (TM) and Failover (SLB) 2) 802.3ad Link Aggregation using Link Aggregation Control Protocol (LACP) 3) FEC/GEC Generic Trunking...
  20. mlgmartin

    LACP Trunking and Network Teaming

    Will it cause any problem in my network if teaming was already done on the server and LACP was not yet configured in the switch? Will it cause a network loop or broadcast problem? Without configuring our switch, I've noticed from the 3 teamed NICs' speed became triple already and the host server...

Part and Inventory Search

Back
Top