Search results for query: *

Has anyone had to patch Call Server in Rls 7.0? Haven't patched in a while and would like some tips? I assume you use UCM but not quite sure where to go.

They PLL unlock events but the CC is not swapping. I will paste history of the event. NWS LD30 BEGIN 03:00 7/1/2010 % % XMI000 20 : PLL UNLOCK EVENT % % XMI000 36 : PLL UNLOCK EVENT % % XMI000 76 : PLL UNLOCK EVENT % % XMI000 84 : PLL UNLOCK EVENT % % XMI000 92 : PLL UNLOCK EVENT % %...

I read a previous post about the XMI000 and replace reseat the Controller cards. What if you are getting XMI000 on most to all Superloops during Midnights. Problem is some cards in multiple SL's are dsibaled in the morning but not always the same SL's or the same cards.

Hello All, I have never setup SIP trunking before so I have a question. I have CS1000M with SIP trunking to 1000B's already setup. We are trying to setup a DEMO for a Cisco Call Mangr. We want to test SIP trunking through the 1000M to make OB calls. Can I use the existing SIP trunk and if so...

Can your ACOD be 2 digits? I had a similar problem with 1000B and I had to rebuild the RDB and Trunk as a WAT. Not sure if this is the same issue as your are having though.

You are correct I did prt out yesterdy and found a TTY programmed on it. What threw was when I PRT's MSDL in LD 96 it did not show a TTY Prgrmed on it. I wasnt aware that it wouldnt show that. Thanks to all for your help!!

I tried to prgramm on Port 0 and it would not take. It said it was being used? There was no connection to port 0 but I am wondering now if its being used by a Psuedo TTY or something?

This is related to a previous post I placed but I am about to program a new PRI and am useing a MSDL card for DCH. I read on another post the port 0 on a MSDL is preconfiged as a TTY? Is this correct? Also does anyone know dip settings on nt5d12 for a MSDL card?

I am going to use the MSDL card so I need to run the cable to from the facplate of DDP to avail port on the MSDL. Based o nthe print out below I can user port 0 on MSDL 12? BSRV NO GROUP 0 GROUP 0 MSDL 13: ENBL DCH 19 OPER PORT 1 .stat ms RLC254 54 00 00 dl GROUP 1 GROUP 1...

I was just notified this is RLS 5.5. I will have to use the MSDL card. JohnPoole you said if I connect to a MSDL card wiht other DCH built on it I will have to disbale to add a new DCH to it? If so what is the process for that? DIS MSDL X then LD 17 add the DCH to the MSDL?

I got this one. I had to change the route & trunk to a WAT. I was getting the page tone but I could not break with a DTMF. CHanging the route and trunk worked like a champ though. Thanks for the response!!

I have a Branch Office with a valcom paging unit. VoIP phones can page. They are registered to main PBX but digital phones built on BO cannot page. RDB and trnk are built as a PAG. Any idea's?

yeh have installed plenty of tmdi but no ddp's. Need to remember about dip settings and cabling.

Thanks to all for your help.

If I have a daughter board(NTBK51) Do I still need to use MSDL? If I do use MSDL if there are other DCH programmed on it I will need to disbable that one when connecting a new one? Here is a print out of CEQU and a DCH I will need to duplicate. REQ prt TYPE PRI254 DCH: 0 DATA: 0 3 cequ CEQU...

Need to add a dual PRI to 81C with a MSDL. Is there a method for choosing your DCH and Slotting the DUal PRI I know takes 2 logical slots but what cards in the network shelf can't it be sloted by?