I am still not able to change the CPND. Same error code as before....
>ld 11
REQ: chg
TYPE: 2616
TN 12 0 2 3
ECHG no
DES 3NE055
DES
AOM
FDN
TGAR
LDN
NCOS
RNPG
SSU
SCPW
SGRP
CLS
RCO
HUNT
LHK
LNRS
SCI
PLEV
AST
IAPG
MLWU_LANG
DNDR
KEY 0 scr 2900 1
HNT FNA
MARP...
OK, I've stumbled along and made some progress.
On the user's exsiting 2616 set, I assigned an open DN to it. Then built the I2002 and assigned to user's extension from the 2616 set. So far so good.
The problem is that now I cannot set the CPND on either type set using ld 95 or ld 20.
What am...
Dear Gurus
I am tasked with moving several users from their current cubes to new cubes and keep existing DNs.
All of users currently have 2616 sets and are going to get I2002 sets in their new cubes.
How can this move best be accomplished?
in ld 20, do I use the MOV or the CPY command? Is...
On my SSC NTDK20JA card, one of the faceplate LEDs is RED, which according to my NTP indicates that the SSC is running a self-test.
The only problem is that the LED has been RED for several days now (over a week).
Should I be worried?
Amad
I set the values for FDN and HUNT to the voicemail extension and the problem is resloved.
However, I am not certain which one (FDN or HUNT) fixed the problem.
I just set up a I2002 set. All seems to be working except that calls are not going to the Voice Mail box. The user has a CallPilot vm box. In CLS of service, I have MWA enabled.
Is there some other CLS value to enable calls to go to VM?
Hi,
Which load will display the number of licences in use or available licences?
Basically I need to lookup the number of available IP licences and Call Pilot licences for my environment.
TIA
Amad.
Ok, after this:
>ld 20
REQ: out
TYPE: 2616
TN 12 0 9 8
I am now getting this SCH0805 message: Specified TN is Invalid. Is this normal?
How am I suppsoed to re-use that TN?
>ld 20
REQ: prt
TYPE: tnb
TN 12 0 9 8
DATE
PAGE
DES
SCH0805
Hmm..almost seems too simple...will I be able to use that TN again for another user? W
Will I need to do anything special to use that TN for another user?
Sorry for my basic questions..but this is a huge learning curve for me.
Thanks.
Amad
Hi,
Can someone please direct me on how to remove the second TN entry for this user? I used ld 20/Easy Change to add the 252 TN and it's working as expected. I need to remove the 012 TN.
Please help.
TN 012 0 09 08 V KEY 00 H MARP DES 2SE57 6 OCT 2009
(2616)
>ld 20
REQ: prt
TYPE...
Ok, I have to apologize for my lame brain.
The DNs I was entering are in fact in use but there's no user assigned to those DNs.
I was mistaken in thinking that because no user is assigned to them, the DNs would be available. Obviously thats not the case.
Using an unused DN, I was able to...
Greetings.
I am attempting to build a i2004 set using the syntax below. The DN I am providing is unused but the error code suggests that it's not a unique DN.
I've tried several unused DNs but I am getting the same error code. What am I doing wrong?
>ld 20
PT0000
REQ: cpy 1
TYPE: I2004
CFTN...
Greetings.
I am attempting to build a i2004 set using the syntax below. The DN I am providing is unused but the error code suggests that it's not a unique DN.
I've tried several unused DNs but I am getting the same error code. What am I doing wrong?
>ld 20
PT0000
REQ: cpy 1
TYPE: I2004
CFTN...
Hi John,
Thank you for your quick response.
If I understand you correctly (since all of the users are on the same network), all I need to do is to move their phone sets from their current office to their new one?
Thats it?!
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.