Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. eddiebullman

    SV9100 Internal Call Routing via PRI

    it can be done but very complex to do one thing though your extensions on the asterisk server will need to be on a different number range from that used by the NEC. you will need to setup LCR on the NEC to route extension numbers on the new PBX via the PIR trunk which then needs to intercepted...
  2. eddiebullman

    Ipecs UCP 100 Hot Desking

    Hi if you look in PGM 101 you should have in the logical column numbers with XXXX(H.D) next to them this will be your hotdesk agents they can't have a physical phone associated to there number the phone that you are logging into phone be set to hotdesk in 111 / 23
  3. eddiebullman

    Converting LIP phones to SIP?

    The short answer is no there is no SIP firmware for them there used to be some LIP-88XX that had sip firmware available. This was answered in a previous post "IPECS LIP-9010 SIP Firmware
  4. eddiebullman

    Panasonic PBX System VoIP and Software based alternative?

    LG UCP is a great platform. hardware or software based now with V5 Only just started playing with 3CX which I am running on AWS but looks ok so far
  5. eddiebullman

    Panasonic pbx ip solution selection

    LG UCP is a great platform. Only just started playing with 3CX which I am running on AWS but looks ok so far
  6. eddiebullman

    FXO

    Hi I am looking for a single port FXO devise to connect an analogue line to a 3CX system that is running on a VmWare ESXi server so I cant use a internal PCI card any recommendations Thanks Eddie
  7. eddiebullman

    LG Cloud/On-Prem

    Hi We used to fit the LG WiFi phones (WIT400HE)and they are a pain i have tried one Ascom i62 handset and it did work with the draytek access points but not very well so we have fit IP DECT instead i have spoken to Pragma about getting Unifi access points certified with Ascom but they did...
  8. eddiebullman

    Ucp and konftel

    Hi Have you tried putting the mac address in pgm235 and you have put the login details in pgm443 you could also put the mac address in pgm442 i am using an Konftel300Wx on the system that i am working on at the moment but it is registering direct to the iPECS D130 IP Dect base and shows up...
  9. eddiebullman

    UCP 100 isdn 30 incoming CLi

    Hi i have an issue with incoming caller display in the UK if i receive a call form out side my local area or mobile the called display is missing the leading zero of the number e.g 7********* or 1508****** i can get round this in PGM151 setting "incoming Prefix Code insertion" to ON and...
  10. eddiebullman

    BT Quantum

    Hi Do BT quantum 8568 phone work on a MiVoice 250 as they appear to be the same as Mitel 8568 thanks
  11. eddiebullman

    eMG80 - CO - deny external calls

    Hi Hasan the first thing i would do is put trunks one to three in trunk group 1 and put trunk four in group 2 programing step 140 this way you can access trunks 1 to 3 by dialing 9 and trunk 4 by dialing 89002 by default you can set up LCR to router the call over different trunk groups but...
  12. eddiebullman

    UCP100 Multisite via VPN

    Hi Paul can you set them to Local but NO on the same Lan setting ?
  13. eddiebullman

    UCP100 Multisite via VPN

    Hi Paul as for the Zone stuff set remote site phones to local-remote and put them in a different Zone and set that Zone to Force Relay
  14. eddiebullman

    UCP100 Multisite via VPN

    Hi Paul If the system sees the handset in remote mode it will modify the sip packets to insert the IP that is set in the 102 & 132 (firewall address) as the address not the internal IP of the UCP or VIOM as it would need to do this to get remote handsets to work the local-remote setting...
  15. eddiebullman

    UCP100 Multisite via VPN

    Hi Paul even if they are set to Remote or remote-local it still won't work because you are not connecting to the public IP of the UCP as the RTP packets are still being sent directly between the phones as for the ZONE data i did see some thing about RTP relay which is what i think needs to be...
  16. eddiebullman

    UCP100 Multisite via VPN

    Hi Paul can you ping from a PC on subnet 200.0.4.1/24 to a PC on subnet 200.0.7.1/24 and back the other way as if you can't do that then it will never work like you have it setup if you have access to the draytek management console there may be some things you can set up on the draytek VPNs...
  17. eddiebullman

    UCP100 Multisite via VPN

    Hi Paul if you are going down the remote phone option just make sure you have plenty of VoIP resources as it will use 2 when a call is made extension to extension what routers are you using at head office and the remote sites
  18. eddiebullman

    UCP100 Multisite via VPN

    Hi Paul what the issue is once the call is setup the UCP100 is instructing the phones to transmit data directly to each other. i have spoken to pragma about this but they have not got an answer for it a shot in the dark can you have a look at what Station IP Attributes PGM122 is set to by...
  19. eddiebullman

    Remote Phone Issues

    Hi Paul i take it that the VPNs are LAN to LAN i don know what handsets you are using but the 9000 series handsets have three settings local on the same subnet as MfIM/UCP local-Remote this is if the handsets are on a different subnet but are not routed via NAT to the MfIM/UCP Remote if the...
  20. eddiebullman

    IPECS LIP-9010 SIP Firmware

    Hi Walter The 9000 series handset are not SIP phones they are LG proprietary VoIP phones so there is no sip firmware LG used to do a 8800 series phone that was sip but i have not seen any for a few years

Part and Inventory Search

Back
Top