Search results for query: *

Thanks Ired for replying Setting a mailbox in that column had no effect. Obt thank you, auto forward works fine, The auto transfer can be as low as 1 minute Thanks again you have been a great help with all your posts

Hello All Thanks in advance I have an NS700 with version 9 on it All calls are answered by CS1 Option 2 goes to ICD 602 if not answered goes to ICD 601 Option 3 goes to ICD 603 if not answered goes to ICD 601 Option 4 goes to ICD 604 if not answered goes to ICD 601 ICD 601 is fna to 500 If...

Hello Attached is a wireshark capture I have 2 channels on the trunk Capture is of a call made from line 1 of the NS700 to my own number giving 503 service unavailable message. I can call out from the NS700 to any other number If I call in to the ns700 from my mobile there is no sip activity...

Hello Mike I have tried both DIL and DDI still no incoming Hello OBT You mention some settings in the sip trunk card for incoming calls Can you clarify those settings please Thanking You

Thanks for the replies Apologies for the delay in replying I am just getting over Covid. I can make calls from the ns700 and I have audio both ways I have the lan cable to the NS700 going through a switch with port mirroring on it and I can see the sip messages to and from the NS700 If I try...

Thanks Fodrod for clarifying that I have made progress in that I can make outgoing calls but no incoming- call does'nt ring at all on the pbx The fact that outgoing calls are ok would suggest the sip side is ok The sip trunk provider uses 10000 to 20000 for voice whereas the DSP card uses 16000...

Could someone please clarify something for me I am trying to set up a sip trunk on NS700 From reading the posts on here I am wondering should I have 2 IP addresses. I believe my trunk is sip peer trunk Details I was given have 1 IP address for sip server ,no authentation .permit is the static...

Thanks for that OBT Always very helpful

Hi Is there any way to see the slot and port that an extension is connected to using PT programming on a TDA 200 Any info on how to assign an extension to a slot/port using PT programming I have gone through all the programming numbers and can't see what I need Thanks in advance

Hello OBT Thanks for that I am up the road a bit from Kilkenny in Carrickmacross

Just a follow up Will the EXT-CID card supply caller id info to all slt on the system Does it matter if an slt is on an SLC card or on the DHLC slot Thanks in advance

Thanks for the reply OBT Very helpful as usual Are you based in Kilkenny by any chance

Hello I have a cordless phone as an extension (slt)of a TDA 30 This phone will show caller id if used directly across the pstn Will an ext-cid card allow caller id through to the cordless phone when it is an extension? Thanks in advance

Thanks for that

Hello All Just a quick question If you initialise an NS700 with licence key info on it will that licence key be lost Thanks in advance

Hello OBT Thanks for that

Thanks for replying WhiteGooner No the switch is in normal position If I use SD memory backup under tools the database is saved Does the system do automatic back ups? Is it the case that the database is saved first to the main board and maintained by the battery?

Hello all I have a tda 30 that loses the customer data after a power down Is the data held on the SD card or on the main board I presume it is on the main board and the battery is dead If so can the battery be replaced ? Thanks In Advance

Hello all Any thoughts about the NS700 and using mobile phones as extensions Do mobile work well as extensions? Will the mobile wake up when a call is incoming I have tried mobiles on a 3cx platform and the push notification does not work reliably. If the mobile phone is asleep the caller gets...

The console is disconnected for the moment I can only access one of the three trunks in the route using a M3820 set