Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. Flyers01

    IOS ISSUES 3550

    boots up to switch: I hit dir and there is nothing there
  2. Flyers01

    IOS ISSUES 3550

    I have several sites doing a upgrade which will require a power cycle of all equipment. I have 3560 and 3550 so far half of my sites had 3550 loose the IOS during boot up. What could cause this. I checked several switches and and there has been no change to the config or register. If you any...
  3. Flyers01

    ALL LIGHTS ON SWITCH BLINK NON-STOP

    can you ping the switch Is also connected to another switches on the network could be a loop
  4. Flyers01

    boost my wifi signal

    Antenna Hi I am looking to boost my wifi signal Do have any suggestion adding a aftermarket antenna
  5. Flyers01

    Cisco 3524-XL-PWR-EN Boot Errors

    This doesn't look good but you can try to FORMAT the flash and load a new IOS and see if that will help.. Remember when you format the flash it erases everything so do not reboot the switch good luck
  6. Flyers01

    Switchport timeout?

    you can use kron or you can config to start up and set the reload at later time and date
  7. Flyers01

    erased flash on 2960 ,swich: only help.

    I also never worked on a 2960 but I know you tftpdnld on routers but cisco switches you need to do xmodem which take hours..... copy xmodem: flash:IOS_filename
  8. Flyers01

    erased flash on 2960 ,swich: only help.

    if you erased the flash and rebooted and you see this switch: you will need to xmodem the IOS on it
  9. Flyers01

    Gigabit on 3560 switch line protocol is down (disabled)

    try to default the interface see if will stay no shut if it does then put your configuration back on and see what happens.. config t default interface gig0/3 end sh int config t int g0/3 no shutdown end show run int g0/3 ! show int g0/3
  10. Flyers01

    CDP Strageness

    I have seen this when we had a 3com switch in between cisco switches/Routers
  11. Flyers01

    fundamental but experience related question on cabling

    Well if it is fiber all u probable needs is to retip the ends I would test fiber and make sure DB loss is under 4 before I wold run cables. Also if you are using gbic look for symbol errors show controllers ethernet-controller gigabitEthernet ?/?
  12. Flyers01

    fundamental but experience related question on cabling

    Can you just run a temp cable to see if that fix your. don't know what type of cabling or issue you have but I would start with replace patch cable then repunch down. if it is fiber test the fiber patch cable also
  13. Flyers01

    send command w/o seeing them

    it is not I don't trust I just don't want them to see passwords I am using I can do this myself without any problems. Just want to have some guys run this script. If there is a way to disable echo for commands I am in business. thanks for your concern
  14. Flyers01

    send command w/o seeing them

    I am writing a script to issues command however I don't want people to see the command being used passwords ip address etc. So is there a way to turn off echo so commands do not echo back to the screen. don't know if this is possible so any help would be great th4nks
  15. Flyers01

    connect to a switch with different ip

    First one worked thanks
  16. Flyers01

    connect to a switch with different ip

    I guess I would use a static route. My not sure this will work cause I can't connect to that switch I am trying to access it all I know is it password and IP address. I might be better doing this vlan database vlan 47 exit config t int vlan 47 ip address 192.168.10.5 255.255.255.0 no shut int...
  17. Flyers01

    connect to a switch with different ip

    switch is connect to g0/5 and it's ip address is 192.168.10.4
  18. Flyers01

    connect to a switch with different ip

    will something like this work thanks vlan database vlan 47 exit config t int g0/5 no switchport ip address 192.168.10.5 255.255.255.0 int f0/1 switchport access vlan 47 no shut exit
  19. Flyers01

    connect to a switch with different ip

    I have a L3 switch and another switch that has a different ip address how would I connect to it connect to switch through fiber cabling how would I configure the L3
  20. Flyers01

    Flash

    How can this happen a rename configs in the flash Directory of flash:/ 88 drwx 192 Feb 28 1993 19:22:48 -05:00 c3550-i5k2l2q3-mz.121-22.EA4 3 -rwx 0 Feb 28 1993 19:23:04 -05:00 env_vars 4 -rwx 346 Feb 28 1993 19:23:04 -05:00 system_env_vars 2...

Part and Inventory Search

Back
Top