Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. carlsclan

    NTP

    Hi there. I need to set up NTP on a 4.1(3) cluster. I have tested this out using the usual MS setup on my test CCM however there seems to be a problem and its not syncing with the NTP source. Does anyone have any good recommendations for NTP on a CCM cluster? Cheers.
  2. carlsclan

    7912 ringtone

    hi all, I am trying to add more ring tones to my 7912 as I only have the default chirp. I have looked @ http://www.cisco.com/application/pdf/en/us/guest/products/ps4153/c2001/ccmigration_09186a00801f011f.pdf and seen that you need to modify the ringlist which I have, however after restarting...
  3. carlsclan

    Unity Question - Turning off "hello"

    yes - this is sorted now. The recording was done on the first page and not the greeting page. Thanks for your help.
  4. carlsclan

    7970 - rebooting

    Hi there, I did a factory reset as it seemed to be looking for a CTL file, and would not register with CCM. it is not even going to the tftp stage as it keeps on rebooting and just goes through this all the time. Any ideas?
  5. carlsclan

    Ip Phone with ATA

    you could always use a FXS card in an NM2V. I have some dect phones plugged into my FXS and works nice along side the IP phones..
  6. carlsclan

    7970 - rebooting

    hi there. I have a 7970 which I did a factory reset as stated on CCO - however it will not come back - it just keeps on re-booting. any one got any suggestions apart from throwing it in the bin?
  7. carlsclan

    Unity Question - Turning off "hello"

    hi there, I have created a call handler with a menu type system. This appears to work fine, however when I get routed to this the "robot" says "sorry" and then my messages are played. Does anyone know how to turn this off?
  8. carlsclan

    FXO ports

    csim will work on any voice router, however if there are no dial-peers in then yes it will not work. No reason why a pots peer cannot be setup also just purely for testing.
  9. carlsclan

    FXO ports

    there is a CLI command in the router which is very helpful csim start 9123 the above will make a call dialing 9123 - match a dial-peer and go out the relevant port.
  10. carlsclan

    CLI on IP phones

    hi there, yeah, this would be pre-pending the number say 5000 - 5999 to say 7445000 - 7445999 make sense?
  11. carlsclan

    router command to show current Conf calls / number of members

    I dont have access to a router at the moment, but there is a command - I think its show sccp connection. but type in show sccp ? this will show you the options. This shows all of the conferencing streams and the codecs they are using!
  12. carlsclan

    Mobility and SRST

    EM only works when the PUB is up, as this does changes to the master DB. So no, when the PUB is unavailable thats it - the phone stays the way it is.
  13. carlsclan

    createProcess Error: 3: The system cannot find the path specified

    Hi there, just installing a CCM 4.1(3) on VMWare, have did the regedits to emulate a MCS. When installing the CCM s/w I get a error come back saying createProcess Error: 3: The system cannot find the path specified and the whole process aborts! anyone seen this before? I have tried this using...
  14. carlsclan

    CLI on IP phones

    this is only for internal, and for long term..
  15. carlsclan

    Cannot browse through PIX

    how can i query the DNS from the PC? if i type in say "ping cisco.com" it is unresolved. Many thanks
  16. carlsclan

    Cannot browse through PIX

    i only have one server on the inside, which is internal. This can ping the ADSL router on the outside, and as i say this can get to the internet if i put an ip address of a www server manually, but will not resolve DNS.
  17. carlsclan

    Cannot browse through PIX

    Hi there, I have a PIX and it is configured as describe on CCO. I have a PC on the inside and a Router. the Outside is connected to an ADSL router. The Router can recieve NTP fine. I am using DHCPD on the PIX and have acquired all the IP stack etc. I can ping the ADSL router fine. I can browse...
  18. carlsclan

    Win2000 Server on COMPAQ dl380 G2

    have posted this elsewhere. however using IE and have no AV at all as of yet as I have just built the thing hence why its strange that I cannot download anything..
  19. carlsclan

    Download problem

    morning all, just loaded this on to my G2. I can get all of the WIN updates fine. However i go to any web site to download files it does not allow me!! this worked fine on another PC using the same WIN2000 Server disk, but not at all on this. What happens is, I either chose to run now or save as...
  20. carlsclan

    Server only showing 6GB when I have a RAID installed

    All is OK now, as this has been sortd! thanks for your help

Part and Inventory Search

Back
Top