Search results for query: *

I dont have access to the other router sine its not in my building its going to take alot of time to get to it

This is what the result of the sh version command SH VERSION Cisco Internetwork Operating System Software IOS (tm) 3600 Software (C3660-I-M), Version 12.1(5)T10, RELEASE SOFTWARE (fc2) TAC Support: http://www.cisco.com/tac Copyright (c) 1986-2001 by cisco Systems, Inc. Compiled Wed 08-Aug-01...

My company has two Cisco 3660 routers with the same IOS 12.1(5)T one of them supports VLANs and the other doesnt seem to recorgnise any VLAN commands i really do not know what to do I copied the IOS from the router which supports VLANS into the one which doesnt since both have the same version...

these are my config interface FastEthernet0/0 ip address 193.222.73.3 255.255.255.248 ip nat outside duplex auto speed auto ! interface Ethernet1/0 bandwidth 2048 ip address 172.30.0.1 255.255.255.252 ip nat inside full-duplex ! interface Ethernet1/1 ip address 193.222.73.33...

i foget but i have a total of 64 public ips donno if by using nat on my serial interface i am going to have problems routing my other ips

i made all the config right but i acant accces the net i can ping my next hop tyhat is my isp's router and his DVB modem but i cant get pass that point i guess my config,s are right since i can ping my next hop pls tell me what to do

how do i config a many to many nat

i am trying to impliment nat i have 30 public IPs and i cant get to config nat on one interface or one ip this are the commands am using int fa 0/0 ip add 10.10.10.10 255.255.255.252 for my WAN int no shut int fa0/1 ip add 11.11.11.1 255.255.255.0 for my LAN int no shut access-list 1 permit...

i dont know how to use this ccommand i have tried but i cant get to ping the next router I recieved i new internet aces for my 2600router and i want this connection to get into my router via fa 0/1 and get to my switch then to my clients via fa 0/0.11, fa 0/0.12 etc using vlans i used the...

i have some public IP's and i want to disable broadcast so i can maximise my public ips i am an isp tech coz i loose two ips on a point to point link i use a 2600 series router network ip ip boacast thats what i have now but i want ip ip on a point to point so i dont loose ip's

i need a cisco 2600 module for two E1 connections and i dont know how to implement snmp on the router for supervision purpose

i just got my certifications and i got a job my company is planning on implementing ISP services which i will be doing the network design routing and switching but i really dont know which protocols to use the network consits of three internet access entries 120 public address a 3800 cisco...

i just got my certifications and i got a job my company is planning on implementing ISP services which i will be doing the network design routing and switching but i really dont know which protocols to use the network consits of three internet access entries 120 public address a 3800 cisco...

Hi, I have a problem with a new Cisco 3640 Router. I have installed two fastethernet modules on it and receive the following public IP from my provider : IP address: 64.110.0.130 subnet: 255.255.255.224 Gateway IP : 64.110.0.129 now, I have a large network and would like to do nat on this...

Hi, I have a problem with a new Cisco 3640 Router. I have installed two fastethernet modules on it and receive the following public IP from my provider : IP address: 64.110.0.130 subnet: 255.255.255.224 Gateway IP : 64.110.0.129 now, I have a large network and would like to do nat on this...

Hi Guys, We intend to do a vpn between 10 offices, Main Office and 9 other regional offices. We basically must use cisco solutions, please advice on a possible network topology and what cisco routers and/or concentrators to use. Note that all sites have access to Internet via satellite, so...

Hi there, I lost my 1700 series cisco password; and tried the usual password recovery procedure. As soon as I Type confreg 0x2142 at the rommon 1; the router displays absolute rubbish. I waited a while and restarted it, it loads cradp like : 2é&ù%ù^^^^^ùù*ù$$$"" etc etc can anyone help ? Thanks

What is the config on routerA ? can you copy and pastye that out ? Second, in router B : ip route 0.0.0.0 0.0.0.0 s0/0 should be your route command. What IP address you have on Ethernet port of router A ?,

not too sure if I quite understand, however old router can be configured to use new router as gateway, you would therefore have to redirect all traffic from old router to new router using IP route command to specific interface that connects both routers. If u are not intending to change any...

Both ends of the link must be configutred to auto; fast switching turned on, otherwise this is strange to me.