Search results for query: *

ip access-list ext 100 permit tcp any any lt 1024 permit tcp any lt 1024 any class-map tcp match access-group 100 class-map others match not class-map tcp policy-map tst class tcp set ip prec 4 class others set ip prec 0 in f0/0 service-policy out tst ip access-list ext 100 permit tcp any...

internet to verizon router via fiber verizon router to 2621 router via cat5 2621 router to 2610xm router via serial through frame-relay switch 2610xm to switch via cat5 switch to pc via cat5 There is no connectivity issue, im just wondering why the pc on the 150.4.4.0 network can ping...

and also it seems like my tftpdnld settings are reset everytime the router reboots. I dont remember this happening with other non xm 2600 routers. Is this also because of the rom or am I missing a command to actually save tftpdnld settings before reseting.

Is the rom image the bootrom? I hope it is. ive, swapped and replaced roms in 2500s but never in 2600 or 2600xm, i guess i will start looking for xm boot rom them. Thanks for all the replys. The router is 128/32, with one dram slot unfilled. A nm-4e is also present.

ok router works with some flashes but not the ones i want it to work with lol. heres the error message. __________________________________________________________ *power up* System Bootstrap, Version 12.2(7r) [cmong 7r], RELEASE SOFTWARE (fc1) Copyright (c) 2002 by cisco Systems, Inc. C2600...

I wish glbp worked for a single router running multiple connections. Only other choice is oer on xm or higher router i think, dont have that good of a router though.

Thanks for replying andy. My current setup is for remote lab pursoses mainly, i want both connections natted outside by the eth ports from the nm-4e while using only 1 fe port from the 2621 for the lans. The remaining eths and fe is mainly used for telnet access to other routers. I just want...

Shoot i forgot i had to go help a friend with a basic wireless router setup lol. Thanks for the replys, i will work on later, cisco is addicting!

Sorry i know its a router question, but if it can work I'll ask about the switch part next lol=).

Im not trying to trunk the eth, only the fastethernet. Below is partial cfg of what im trying to do, I just want to know if it can work or not. I want to avoid plugging any cable from the nm-4e to the switch, just doesnt seem to work right, always flashes orange, ive tried all duplex and speed...

Heres my situation.... I have a 2621 with a nm-4e and a 3550 48 emi. I have a dsl connection and a cable connection each connected to an ethernet port on the nm-4e. I would like to create 2 lans (one for each connection) using only one fast ethernet port from the 2621 to the switch. Please let...

Other than the physical differences like slot and ram capacity, can someone tell me of some other advantages that the 2801 has over 2621xm.

nevermind i fixed it. I think the problem occured because the 2950 doesnt allow for .tar uploads to flash. I had to xmodem the new ios. Is it possible to tftpdnld an ios to flash for the 2950?

Interrupt within 5 seconds to abort boot process. Boot process failed... The system is unable to boot automatically. The BOOT environment variable needs to be set to a bootable image. switch: _______________________________________________________ Ok what did I do wrong and whats the cure...

thanks chafetan

Hi kisco, it works again but only with the vmware pc. I have no clue why. When I change the vmware gateway to .252 it gives me more upload and when its on .253 i get max download and about half as much upload(about 1 meg only). When I use the virtual gw address, it seems like it will switch...

Ok i thought i had the glbp working on the vmware pc, but now it doesnt work=(. Can u guys help me fix my configs to make it work? 2620(cable), 2621(dsl) both are connected to the switch(3550) on vlan4 and below are the cfg for each. Thanks everyone! version 12.3 service timestamps debug...

thanks kisco, i got it working but it only works on a vmware pc and not on the actual network pcs.

Can load balancing be achieved using 2 different service providers (1 cable, 1 dsl) or can it only work with 2 connections from the same service provider? Thanks for answering all my questions=)

thanks to both. I'm only running xp pro joamon