Search results for query: *

to maksg Thank you very much for your information. This was the key to solve the problem! In my search I missed this command "media-type". Thank you again, it much appreciated.

burtsbees, below you will find the sh run, sh cdp neigh det, sh interfaces stat. As you can see the 2960 gi0/2 100MB SFP is in half duplex mode. I really wonder why! ASW2> ASW2>en ASW2#sh run Building configuration... Current configuration : 3880 bytes ! version 12.1 no service pad service...

burtsbees, I'll do a sh run etc. today. To your last reply: I have not a Gbit SFP but a 100Mb SFP module (GLC-GE-100FX) in the 2960 because the 2950C is 100Mb only. According to the Cisco documentation this module is compatible with the 2960...

sorry guys for the delay. I have solved the problem. The PVID was not set correctly.

Hi, We are interconnecting a 2960 equiped with a cisco 100MB FX SFP to a 2950C. We get errormessages telling me there is a duplex mismatch: 00:36:48: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on GigabitEthernet0 /2 (not full duplex), with ASW2 FastEthernet0/25 (full duplex). I have...

Hi all, I am trying to setup 3 Vlan's and ports on 2 switches. What I have done: switch#1: vlan1(default), Vlan2, vlan3 switch#2: vlan1(default), Vlan2, vlan3 switch#1: port 1/0/1, hybrid, untagged vlan2, tagged vlan3 port 1/0/2, hybrid, untagged vlan2, tagged vlan3 communication between port1...

Hi all, I have a question about sip trunking from a BCM50R3 to a CS1K NRS. This is all new to me so forgive me if it's a dumb question. We have enabled 4 sip trunks at the BCM50. We use a 4 digit numbering plan. What we need is to be able to call another site which has a 4xxx internal numbering...

Thanks all, For now I am still having trouble, even on a BCM400 4.0 I have opened a case at Nortel and awaiting for answers. I will update you with info if available.

Hi all, I am having problems stacking BES220-48T-PWR switches. What I have done: - checked if firmware of both are the same: OK - Set switch 1 at the back to "base" - Connected both switches from up-to down port and from down-to up port. In other words I created a loop. (according to the manual)...

@gwebster: Thanks, is it possible to load the firmware outside the BCM? I mean, running TFTP or something on my laptop and load the firmware from there? @snowman50: Thanks, Ill give that a try!

@ Snowman50: We have set the card in resourses correctly. Status is enabled but the lines for the first loop are set in BlocB by the system. @ DBrewsky: We do use routing for the PRI for outgoing calls. We need the BRI for a GSM gateway. So we created a route to this BRI for mobile numbers. To...

We are unable to register 12xx sets to a BCM450. The problems we encouter are as follows: BCM is setup as DHCP server. registering 11XX sets => no problems registering 200X sets => no problems registering 12xx sets => trouble When connecting the 12xx set the set displays information: Loading...

At the moment we are configuring a BCM450 and we encounter some problems: We have a BCM 450 loaded with a DTM module and a BRI module. According to the documentation we have to assign lines to the modules which we did: DTM (Main MBM4) => lines 91-120 BRI (Main MBM3) => lines 61-68 All...

Cluebird and Burt, Thanks for your replies. It makes a lot clear to me. The router we will use will be a cisco and will be used as a router on a stick. Configuration will be no problem. Thanks again.

Burt, if I understand right you say IF I use different VLAN's to seperate 2 networks I always have to use a router? So, the only solution is to create VLAN200 in the 2950 as well to get it work if I don't have/use a router? My confusion is propably that I have set the same situation for...

Hi, I had a problem connecting 2 switches together. This is the situation: one new 2960 switch, port f0/24 not configured in trunking mode. Just a standard port. Only this port is assigned as switchport access VLan200. The reason is that the first 12 ports are VLAN100 and port 13to24 is VLAN200...

Dasheen, thank you for your reply. So, if I am correct, first I have to program a feature key on the handset itself before to be able to use the System speed dial? I assumed all functionality of the BCM features where integrated into the handset. Because there is no feature-key (the nortel...

We have a site running a BCM50 R2.0 with WLAN 2211 handsets. On a digital or IP set people can use feature 0 to use speed dial. How can this be done at a 2211 handset? Maybe I overlook it but I can't find the use of features Thanks in advance for any help.

Thanks guys! Dewey's option is easier indeed but anyway good to keep in mind that it will forward all calls. (internal calls as well I suppose)I'll try both suggestions.

Hi, We have a BCM1000 v2.5 Our mainoffice tel.number comes in at targetline 241 wich is handled by our receptionist (operator). Is there a way to create a ringschedule say "night" where all calls at TL241 will be redirected to a predefined external number? Ofcourse use of F84 is possible but...