Search results for query: *

Many thanks feherke, I knew it was missing something simple and obvious.

Hi, I'm trying to figure out how to read to a variable some of the info phpinfo(); outputs, in particular I would like to read the value for "sendmail_path" that can be seen on the output of the phpinfo(); I'm sure it is pretty simple, and I'm almost ashamed to ask, but so far I haven't...

Is the built-in Windows XP firewall on? If so, have you checked if there is some XP firewall setting blocking your VPN IP Range? Try to disconnect the XP firewall to test.

Hi, I have a network consisting on 55 Workstations running Windows XP, and three servers running Windows 2003 and exchange 2003. I'm about to purchase two licenses for windows 2008 R2 and Exchange 2010. My doubts are related to the CALs I need to buy. For Exchange 2010 it is clear that I...

Hi, does anybody still have a copy of the good old webinterface 4.2 lying around? I really need that file. As usual, Citrix besides changing product names every now and then, does not allow to download old files. I can download 4.5 from Citrix, but it is no good as it doesn't run in Windows...

Well, its been more than a week and the router has not crashed again since. The solution I have adopted is to set the FastEthernet 0 interface to 10mb Full duplex, so far that seems to do the trick. That way I do not have to rate limit the whole VLAN1 interface rendering the 877 switch...

I would advise to set the SLA pinging to the HQ over the main link, and if the pings do not come back then switch over. I have seen cases in which the link was up but not sending anything.

@burtsbees Hi, I do not want to sound pedantic, but cisco says that those values are a recommendation and not mandatory. Trust me I was having lots of disconnected transfers until I did mtu = 1478 / mss = 1300. ----------------8<----------------- From cisco: If you are configuring the ip mtu...

@burtsbees The reason for the low MSS is that I found that when lowering it a bit I get less disconnections from certain sites, you know those cases when transfer speed is good then degrades quickly and then the connection breaks and you have to keep retrying the transfer all the time. For the...

Hi, here is my config, but I think that %C870_FE-4-QUEUE_FULL stands for: "870 series router fast ethernet module error number 4 Queue full". There is only a single port being used on the router and that is FastEthernet 0 not 4. -----------------8<------------------------ version 12.4 no...

Nah, crashed again today... the same symptoms lots of drops and lots of: "%C870_FE-4-QUEUE_FULL: Ethernet Switch Module transmit queue is full" Back to square one, this time got a lot of dumps from the #debug sanity command. I'll feed the dumps into a spreadsheet to see what I find.

@Burtsbees, Hi, thanks, I realize that I need to read how the rate-limit command works. As you pointed out I misinterpreted what the parameters are for. So far uptime is 1 day, 23 hours, 27 minutes without any strange incidents except for those in the logs which happened just now...

@burtsbees Hi, thanks, seems I missed a "0" :-)

@burtsbees Hi, there is no "clock" command under the atm configuration, however I modified my dialer to include rate-limit outbound and inbound. This is what it looks like now: interface ATM0 no ip address no atm ilmi-keepalive hold-queue 224 in end interface ATM0.1 point-to-point pvc...

Nope, the router still has trouble even if I limit the output rate of the interfaces... The topology is as follows, there are two workstations plus a laptop which is on sometimes. The laptop connects wireless to the router, the workstations connect to a 8 port 3com gb unmanaged switch. The...

Hi, As I have a 6mb/1mb ADSL line I issued the rate-limit command in my Dialer interface as follows: rate-limit output 8496000 90000 100000 conform-action transmit exceed-action drop 8496000 because cisco says less than 9 megabits and 90000, 100000 because I have a megabit upload speed. Is...

@North323, I think I get it now reading your explanation; the virtual interface is not the Vlan, but the WAN virtual interface... So the problem lies in my external link and not on the inside part of the lan... That makes sense, I was wondering why the 100mb switch built-in the router could...

@burtsbees Hi, Thanks for your reply, I never had to use such a thing before, I'm not a Cisco expert by the way. When I try to configure the interface rate-limit requires "input" or "output" besides the rate, what should I use? By the way, do you know why could this problem be happening...

Hi all, I have an 877w Cisco router which is hanging from time to time and when it does it doesn't respond to ping or process any traffic at all. The lights blink from time to time and that is all that it does when the trouble appears. When I check the console using the serial cable the...

Hi again, Got hold of "PSE400W2K3R05.msp" Still looking for: "PSE400W2KR05.msp".