Search results for query: *

Tom Thanks for your input. I think this forum is much better than Catalyst support. I also checked my remote end and see 5 VCM channels as well. Dont I need VCM cards along with VCM channels? When we bought the unit we got some licenses which included VCM channel license. I dont see any...

1mS PRN: Monitor Started IP=10.10.10.113 IP 406 DS 5.0(15) Canton406v2 1mS PRN: LAW=U PRI=0, BRI=0, ALOG=8, ADSL=0 VCOMP=5, MDM=0, WAN=0, MODU=1 LANM=0 CkSRC=0 VMAIL=1(VER=2 TYP=1) CALLS=2(TOT=4249) 327mS RES: Tue 13/4/2010 10:23:11 FreeMem=37777552(2) CMMsg=6 (8) Buff=100 595 500...

I was wondering how was that working in 3.2(67) without the VCM card? Do you think it wouldnt have worked?

Bas1234 - Yes I did ticked Advertise huntgroups tlpeter - Yes I see IP Office SCN and selected that as well. I did some reading on this and will I need VCM cards and any additional licensing for thsi to work?

I created the VPN between the locations and can dial the extensions of remote location however I do not see the remote huntgroups on my system. I do see Redistribute hunt groups option on the IPOs. When I check the IP Line config, I do not see Voice Networking option in 5.0(15). This option was...

Hi I have an Avaya IP406 at my end and another Avaya IP406 at remote office. Both are upgraded to 5.0(15). I have a requirement that when a call comes in it should ring on the local and remote hunt groups. Hunt groups are configured at both ends. I would like to know how can I get this...

As I found the hardware is not supporting ip unnummbered, I have changed the configs as below ASA route outside 0.0.0.0 0.0.0.0 210.55.6.50 icmp permit any echo inside icmp permit any echo outside icmp permit any echo-reply inside icmp permit any echo-reply outside icmp permit any...

I have my config pasted on the link below. Can you please check this and advise. This is really urgent to me. http://www.tek-tips.com/viewthread.cfm?qid=1312952&page=2 Appreciate any advise. thanks

hi thanks for the reply. I am trying to access internet from the local site and seems that it doesnt pass through the firewall. though I dont have acls from inside to outside, there is something stopping me to access the internet from local network. By the way, I have already used the command...

hi This is a nice thread. Just want to relate my problem with this thread. Today I had a problem while setting up VPN from site-to-site. I have acls to allow all local traffic to remote network via the vpn as interesting traffic through crypto map without natting. I have all other traffic going...

Hi I have configured a site-to-site IPSEC VPN and seems like I have some basic issues. Can you please advise? can ping from LAN to ASA inside interface cannot ping from LAN to ASA outside interface can ping from ASA to internet (eg:cisco.com) can ping from router to internet (router is...

mingtmak, I have attached my configs and setup on the thread below. Can you please check the configs and advise me further. http://www.tek-tips.com/viewthread.cfm?qid=1312952&page=1 thank you

Hi I am working on VPNs for the first time and I have the setup and config as below. Can someone please check these configs and advise if any changes required. Local network remote network switch - ASA - 1700 router - internet(T1) - ISProuter - pix - switch A...

Hi, thanks for that. What about the traffic coming from internet accessing internal servers, should I do the natting on the router or on ASA? My requirement is anything coming from internet to wan interface on router (e1-3.3.3.1) should be natted to ASA outside interface (2.2.2.1) and...

mingtmak, I believe you have a router after the ASA connecting into the internet right? If so, does it have the basic config and allowing all traffic coming from the firewall?

Hi Thanks very much for your reply. As I would be doing the Natting on the firewall, I believe the router should be configured with basic configuration and will be passing all the traffic from the firewall to the internet right? thank you

mingtmak, thanks for your response. I almost understood your config. I am a bit confused when I see relate to the config from Cisco website you have mentioned. http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a00804675ac.shtml In this same acl is...

Hi I am new to firewalls and I am trying to do a setup as below. Can anyone advise me if this is the right setup. switch-->ASA-->router -->internet-----> pix --> switch. local remote I am confused to have the router between ASA and PIX. Is this really...

Brent or Darren just using the above example to make my question simpler, global (Outside) 1 82.111.251.83-82.111.251.94 netmask 255.0.0.0 static (Inside,Outside) 82.111.251.83 172.16.100.4 netmask 255.255.255.255 access-list Outside_access_in extended permit tcp any host 82.111.251.83 eq 3389...

sorry I meant where is your 10.100.103.0 network?