All I get from the extended ping is "success rate 0/5". I've tried Verbose, Record, Strict, Loose....what am I not doing...where is the debug information to copy and paste?
More info please.
Thanks for your patience.
Ummm, I can't get the debug to log extended (or otherwise) ping failures. It seems to log only successful pings.
Commands I'm using to do debug logging
R1#(config)[terminal] logging buffered 4096
R1# debug ip icmp
(Telnet into R2 exec same)
R1# ping (extended)
R1# sh log
Here are the ping results from Router1 Ethernet to Router2 Serial
Router1#ping
Protocol [ip]:
Target IP address: 10.237.1.4
Repeat count [5]:
Datagram size [100]:
Timeout in seconds [2]: 4
Extended commands [n]: y
Source address or interface: 10.237.0.2
Type of service [0]:
Set DF bit in IP...
A tracert to an IP on the remote LAN (Router2) runs right out through our Internet connection to our ISP's DNS servers which of course say that the "Destination host unreachable" Hmmm...
The people that are registered by the Certifier ID (usually the Domino Server ID) will be in the PAB (Public Address Book) on the Domino server. You can't deploy a Domino server with out creating or being part of a PAB. The PAB database file name on the server (by default) is called names.nsf...
I cleared the counters on both serials.
Please explain the "Extended ping" prodedure - and from the serial to where?
Tracert from a client on LAN1 to another machine on LAN2? or to the Eth0 int on the other router?
Did I tell you guys how great you are?
philmcgarry...
I cleared the counters on both serials.
Please explain the "Extended ping" prodedure - and from the serial to where?
Tracert from a client on LAN1 to another machine on LAN2? or to the Eth0 int on the other router?
Did I tell you guys how great you are?
philmcgarry...
Router2 (sh ip int brief)
Interface IP-Address OK? Method Status Prot
ocol
FastEthernet0 10.237.128.2 YES NVRAM up up
Serial0 10.237.1.4 YES NVRAM up up...
OK! Sorry about that. It has been corrected. Router2 Serial int is now x.x.x.4 and Router1 serial int is now x.x.x.3 Still no packets routing.
router rip
version 2
network 10.0.0.0
no auto-summary
Router 2 (sh int ser0)
Serial0 is up, line protocol is up
Hardware is PowerQUICC Serial
Description: connected to ROUTER1
Internet address is 10.237.1.4/24
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback...
No alarm lights on the CSU/DSUs (Kentrox DataSmart 658)
Here we go, Router1 (sh controllers ser0
Interface Serial0
Hardware is PowerQUICC MPC860
DTE V.35 TX and RX clocks detected.
idb at 0x810BCE54, driver data structure at 0x810A3034
SCC Registers:
General [GSMR]=0x2:0x00000030...
Router 1 config
!
service timestamps debug uptime
service timestamps log uptime
service password-encryption
no service tcp-small-servers
no service udp-small-servers
!
hostname Router1
!
enable password xxxxxxxx
!
no ip name-server
!
ip subnet-zero
no ip domain-lookup
ip routing
!
interface...
Here is the show ip route for router 1:
Router1#sh ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.