Search results for query: *

I can't answer on the Aiphone door phones but a Viking PAN-1A adapter will let you use Viking door phones in place of Panasonic KX-T30865 or KX-T7775 door phones.

Looking at a KX-NS1000 I don't see any obvious way to block the paging codes by user. How about just change the paging codes? See PBX Configuration > System > Numbering Plan > Main > Features tab.

Correction - the status lights are the same on both NCP and TDE processors.

That's good to know. I was looking at a NCP processor card the other day and wondering the same thing. Just 2 differences I noticed - 1. There are no status lights on the NCP processor card itself, they are built-in to the NCP front panel. 2. The TDE processor card has 2 Paging ports and 2 MOH...

Not sure if you are in the US or not, but the AK's Panasonic in the US supplies will only work on US Panasonic product. Not sure how it works in other areas. Here is a listing to a dealer who can provide Panasonic US AK's - eBay item number:123758191260.

To see all the activation keys currently installed, go to Config > Slot > Virtual Slot > click on Activation Key button. The AK's are still available from Panasonic through authorized dealers. There's no cost for the AK's now. I can help you on those if you want, I charge only for my time.

Sounds like a activation key issue. Check the number of IP phone extension licenses loaded on the NCP. You can also try unplugging a working IP phone and then try the new IP phone again. If it's an activation key issue it should work.

If you are in the US, Panasonic has changed the free temporary activation keys for NCP and TDE PBX's to free permanent activation keys. You just need to get in touch with an authorized Panasonic dealer to get them.

Not sure if you've solved this already, and I'm not sure exactly how you have the NS700 configured, but let me know if you've already tried this - The "Overflow to Mailbox for Call to ICD Group" should be set back to enable. Then at PBX Config > CO & Incoming Call > DID Table > UM Service Group...

I noticed you used 16 bit. My notes show this for the NS audio file format - WAV file G.711 PCM codec 8 kHz, 8 bit sampling rate Monaural A-law or u-law encoding 32 MB maximum of G.711

Just saw your older post - I had a similar problem with what might have been corrupted system files on a KX-NS700. What solved it was initializing it and then doing an upgrade to a newer version of the firmware.

On the US version I think you can assign a G-DN button and assign the CLIP number to that ICD group. When you dial out press the G-DN button first and the CLIP for that ICD group will go out with the call.

Can anyone confirm there is no problem running Sidekick 98 on a NTFS disk on Win XP? I'm considering converting a FAT32 drive to NTFS.

Just received my new November issue of Telecom Gear. It's been revived under new ownership.

thanks Jerry, you hit the nail on the head. You've got to have a ring & appear for the target line on the extension for the forwarding to work.

Thanks, I already tried tech support.

Anyone successfully used the Phone Assistant software? I've set it up(V1.6)with a KX-TDA100 V3.2. Everything's fine except I can't get the "Select" tab on the PA Supervisor Pro (Status) to show up. I've licensed both the PA Pro and PA Status Pro on the server. No select tab so the supervisor...

Have you checked the TVS100 settings? It should be set for TD1232 integration, mwl notification should be set in COS. Can you leave a test message and get a mwl?

Thanks - I tried forwarding to a number with # at the end, no difference. It completes the call and then cuts it off. I tested an external transfer, works fine. It's a 12 trunk fractional PRI, there's no CSU, the CLEC has a Cisco box which breaks out voice (PRI) and data (on demand type).

Thanks, no haven't solved it yet. Is your case also using a PRI?