Search results for query: *

Hi this is my topology Host1--------GK------------GK2--------Host2 zone 226.... zone 5.... Very thanks

hi !!! Yes i have to configured the dial peers but no function!!! in the GK this are the dial peers dial-peer voice 1000 voip destination-pattern 226.... session target ras dial-peer...

hi I have two gatekeepers (MCM-cisco2621mx, with ios 12.3 jsx) the configuration of GK is: gatekeeper zone local GK mio.com zone remote GK2 otro.com 192.168.10.10 1719 zone prefix GK 226.... zone prefix GK2 5.... gw-type-prefix 1#* default-technology lrq forward-queries no shutdown ! the...

Hi I have one problem when i configure ipv6 address on the interface fast 0/1 of the cisco 2621XM ios Version 12.3(7)T. i have one tunnel with prefix /48 interface Tunnel1 no ip address ipv6 address X:X:X::2/48 tunnel source x.x.x.x tunnel destination x.x.x.x tunnel mode ipv6ip And when...

Hi everyone I want to control the broadcast packets on the switch catalyst 4948 i had to configured the interfaces with: interface fastethernet 1/1 storm-control broadcast level 10 storm-control action shutdown but i have two cuestions how can i to estimate or calculate the best value on...

hi!!!! i cant to get to dial the extension number of PBX. i dial the ACOD 1500 but i cant to dial another number. Anything or something about this topic??? can somebody help me??

hi i can to get dial tone with ACOD, but after dial another digit (0-9) not call nothing!! it not dial! so what i can?

hi marc3lo i have new problems but 1.- LD 17 no problems 2.- ABCD Signaling bit tables *********************************** ld 73 SICA 04 IN/OUT CALLS IDLE (S)1001 IDLE (R)1001 FALT (S)UNUSED --->i cant to change this is 0000 FALT (R)UNUSED --->i cant to change this is 0000 SEZA (R) UNUSED...

Hi marc3lo!!! Please help me well ! 1.- LD 17 REQ CHG TYPE CEQU DTI2 type the loop number were my card is inserted (but if it already exist??? for example DTI2 2 1??? i have to add on 3 1??? and after insert on slot 3??) 2.- LD 73 REQ NEW TYPE DTI2 FEAT ABCD SICA 4 and others parameters...

hi cmptsul01 yes this printout of the configuration is already set i havent to configured nothing, i have to type PRT!!! but, the card DTI2 is in the slot 2: DTI2 01 02 ************ the ABCD signaling has the sica table 01 and the loop 3 already set My cuestion is, have i to add the...

Hi marc3lo!! thanks! Well i have the next on meridian option 11c: Add DTI *************************************** ld 22 PT2000 MARP NOT ACTIVATED REQ prt TYPE cequ CEQU MPED 8D SUPL 000 004 008 012 016 032 036 040 044 048 064 068 072 XCT 000...

hi cmptsul01 very thanks for yourr help! So. I DON'T HAVE EXPERIENCE IN NTAK10-DTI BUT IF YOU TELL ME HOW I DO IT, I WILL BE VERY HAPPY! What is or what is more efficient, have a DCH or in CAS mode? How can i ask the ABCD SICA table to connect to Cisco Equip??? How can i Set the DTI2 loop in...

Hi Jonhpople!! Before that someting thanks! The 2.0 DTI card not is PRI (or T1), its E1. i have to reading that qsig is signaling for a PRI T1 card. i dont know if you can help me ?? thans

Hi well, i need to connect E1 DTI card of meridian option 11c with a cisco router [E1 interface(VWIC2-1MFT-G703]. I have looked in this forum about this and it say the next: The following is a summary of the tasks in this section: 1 LD 17 – Add a 2.0 Mb DTI card. 2 LD 73 – Define the 2.0 Mb...