Search results for query: *

Hi, Does anyone know how to "force" CallManager to create a UDL file? or where this file lives? I have done a file search on the CallManager server and can't find it anywhere. Thank you

Hi, Has anyone out there successfully linked AI Office to Cisco CallManager 4.2? Aparantely I have to link the AI Office collector to a .udl file created by CallManager. I have done a search for any such a file on the CallManager server but there are none. Anyone has any ideas about how...

Hi, I wonder if anyone could give me some light regarding the following In one site I have a 2811 and in the other site I have a 2811 with a PIX506E. Both routers are running CallManager Express with IOS versions: c2800nm-adventerprisek9-mz.124-4.XC4.bin...

Hi, We have Cisco CallManager Express installed in one of our sites and I was wondering if the following would be possible... The customer has a GFI Fax on-site, can I route the traffic to this GFI Fax through a Modem WIC-2AM card and if yes, I would appreciate some hints for the...

Hi, I have a 7914 Expansion module installed next to my 7960. The expansion module seems to be working fine ... besides the lights... According to Cisco documentation the lights should do as follows: Off/dark Line available Green, steady Line in use by you; you may also transfer the call...

Hi, I am trying to get an expasion module 7914 to work with my 7960. These are some extracts from my config: CONFIG (Version=4.0(1)) ===================== Version 4.0(1) Cisco CallManager Express load 7914 S00104000100 load 7960-7940 P0030702T023 At the moment when I go into the...

Hi, I have recently installed two Cisco 857W wireless routers and after installing them at two different houses, I am having exactly the same problem in both instances. The problem I am experiencing is the lack of signal as soon as I move into a different room/floor. In one of the cases, I...

Hi, I am expereincing the following problem with a Cisco 1701, flash:c1700-advsecurityk9-mz.124-5.bin. I telnet into the router, type the terminal monitor command and then the fun begins...... if I do a "debug ip icmp" and do a ping somewhere I get the following... TEST#debug ip icmp...

yes, both Dialers are bound to Virtual-Access 1 and 2 respectively ...and after applying the "ip load-sharing per-packet" on both Dialers.....still the same any more ideas?? cheers

Hello again, The router is a 2621XM I am not doing any VoIP interface ATM0/0 no ip address no ip redirects no ip unreachables no ip proxy-arp no ip mroute-cache no atm ilmi-keepalive pvc 0/38 encapsulation aal5mux ppp dialer dialer pool-member 2 ! dsl operating-mode auto no...

sorry I forgot to mention in my previous post.......... would "Multilink PPP" be an alternative??? cheers

Hi, I need to load balance traffic from one router over two ADSL lines but I only have control over the on-site router, not over the ISP router. Is there a way of doing this...I've been reading trying to find some information regarding the subject but in all the papers they seem to think...

...Router_2#ping 192.168.0.4 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.0.4, timeout is 2 seconds: *Apr 4 22:49:18.774: HSRP: Et0 Grp 1 Hello out 192.168.0.3 Active pri 222 vIP 192.168.0.1 *Apr 4 22:49:19.790: HSRP: Et0 Grp 1 Hello in 192.168.0.2 Standby pri...

Hi, sorry that was a typo mistake......a copied and pasted... I was already using 192.168.0.2 on the Ethernet interface for Router-1

Hi, I'm running HSRP in a small LAN.... I am using two 800 series which are connected to a 2960Switch... the configuration in the routers is as per below.... For Router-2: interface Ethernet0 ip address 192.168.0.3 255.255.255.0 standby 1 ip 192.168.0.4 standby 1 priority 200 standby 1...

...when I debug I get the following..... Mar 1 00:15:26.228: IP: s=192.168.82.2 (FastEthernet0/1.82), d=100.100.100.100, len 60, policy match *Mar 1 00:15:26.228: IP: route map OutDialer2, item 10, permit *Mar 1 00:15:26.228: IP: s=192.168.82.2 (FastEthernet0/1.82), d=100.100.100.100...

Hi, I have a 2621 with a WIC 1B S/T card and a 2811 with a WIC 1B S/T V3 card I have connected the two ports with an ethernet cable and configured the 2 Interfaces but I can't ping neither of the interfaces......is this because I don't have a "proper" D channel??? Is there anyway of...

Yes, you are right.......just a typo....my mistake.... the correct form would be set interface Dialer2 or maybe .....set default interface Dialer2

Hi, You are right. I am not very sure about why they've put that "route-map route-nat" on all the sub-interfaces....as it stands right now, it doesn't seem to be doing anything as this route-map does not seem to be configured anywhere... Sorry, forgot to mention, I didn't do this...

! ! Last configuration change at 12:23:14 UTC Thu Apr 6 2006 by crucial ! NVRAM config last updated at 14:17:05 UTC Wed Feb 15 2006 ! version 12.2 service timestamps debug datetime msec service timestamps log datetime msec service password-encryption no service dhcp ! hostname TEST_router ! boot...