Search results for query: *

Thanks Andy, Got it, I'm familiar with the 6500 and 4500 switches but not with the stack switches tough. Last question, with this configuration, both switches will share the configuration right?, if the master goes down, the slave will take the role and will transparently keep working without...

Hi Andy, Thanks for your reply, really appreciate. So it means that, i would have 2 routers but internally only one big switch with 96 ports and each port has nothing to do with the other, i can have GigabitEthernet 1/0/1 assigned to do one thing and GigabitEthernet 2/0/1 other right...

Hi Guys, We need to implement 2 3750 stack switches for an emergency purposes, I've have never configured switches in stack before, i was reading the Cisco guide but i can't find what i need to know, those switches are new, never been configured, OK here is my question: We will have one Master...

Hi, I'm using a 2650 router running c2600-ik9o3s3-mz.123-26 IOS, Yes i'm using both wic slots with wic-1adsl cards, Yes my DSL is PPPoE. Thanks.

Hi, Yeah i see this: no network-clock-participate slot 1 no network-clock-participate wic 0 Is this good or bad?, why is this happening?

Hi Guys, Everytime i reboot my router i got this message, what does this mean?, how can i remove this?, i got 2 wic-1adsl cards on the router. Thanks in advance.

Hi Guys, I have 2 DSL connection and need some help in the configuration, both are working but i'm not sure if my configuration is correct, here is the config: interface ATM0/0 no ip address no ip mroute-cache no atm ilmi-keepalive bundle-enable dsl operating-mode auto ! interface...

Hi Guys; Where can i find info about NAPT-PT configurations on cisco routers?, i'm in a project with a friend, we almost have all the local network running with IPv6 but we need NAPT-PT, i only have /29 subnet assigned by my ISP and we have more than 6 host in our LAN. Thanks in advance.

Hi TGaylor, Do a sh ver and check if you have your Configuration register in 0x2102, if not go to conf t and enter this cmd: config-register 0x2102 save and reboot the router, after that it will save the configuration, this is in case you don't have this config register. Hope this help.

Hi, Change this: ip dhcp excluded-address 10.1.0.1 255.255.0.0 ip dhcp excluded-address 10.2.0.1 255.255.0.0 for this: ip dhcp excluded-address 10.1.0.1 10.1.0.1 ip dhcp excluded-address 10.2.0.1 10.2.0.1 Change your DHCP Poll for These ones: ip dhcp pool vlan11 import all network...

Hi Guys, I have at home dual adsl connection (7Mbps each) and i need to know if a 2651xm router with 256/48 can handled that?, it will run Firewall, NAT, DHCP and some ACLs and around 10-15 PC's accessing to internet, by cisco the 2651mx can handled around 20Mbps but i'm not sure with all the...

HI vipergg, I'm not following you, can you please explain me this again?, i'm using a power adapter to connect the AP, this AP has two mac address, one for the ethernet port and one for the dot11Radio 0 interface, and the AP is attached to port 24 on a 2950 switch. Please can you explain me...

Hi Guys, I'm dealing with this problem, i have a second AP 1120B as a repeater, got everything configured but the dot11Radio 0 is on Reset status and protocl down, i found this on google: CSCsi24761—The 802.11a radio in 1130 series access points sometimes remains in a reset state...

Hi, Ok, here is my configuration on the AP: ! version 12.3 no service pad service tcp-keepalives-in service tcp-keepalives-out service timestamps debug datetime msec localtime show-timezone service timestamps log datetime msec localtime show-timezone service password-encryption...

Hi Guys, Attempting to setup a Cisco 1200 to give out private DHCP addresses to its clients. I have added the following statements, however the AP isn't giving out any addresses. ! service dhcp ! no ip dhcp conflict logging ip dhcp excluded-address 192.168.50.1 192.168.50.5 ! ip dhcp pool AP...

Hi Guys, I want to give access to my home cisco lab to a couple of friends to give them the change to practice before the exam, i have setup SSH to accept connections to my access server, i'm the admin and have privilege 15 but i want to assign a lower privilege to my friend because they don't...

Hi Guys, Thanks for your help, i can now connect to my access server remotely via SSH, after few days looking the configuration in my gateway router i noticed that i didn't put this cmd: IP NAT INSIDE under interface vlan1 , after added this cmd everything is working, again, thank you guys...

Hi plshlpme; Nothing, i can't access my access server (R2) from outside, i tried everything and nothing, can you please check again my configuration? Router1: NAT Configuration: ip nat pool IP-BLOCK 206.xx.xx.225 206.xx.xx.226 netmask 255.255.255.248 ip nat inside source list NAT pool...

Hi plshlpme, Do i need to add this to my WAN access list? permit tcp any host 206.xx.xx.230 eq 22 yes, i have the static route that you told me before in router 2; ip route 0.0.0.0 0.0.0.0 192.168.200.1 Thanks in advance.

Hi plshlpme, The problem right now is, i'm using putty to connect me to my gateway router (R1) and i can't do it, i got this error: putty fatal error Network Error: Connection time out When i ping the static ip address 206.xx.xx.230 i only got time out, the only ip address i ping and got...