Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. AndrewAllen

    Weird Cabling Issue: Cat65xx+x6148-RJ45V & x6348

    ADB100, Re: Fluke/cable testers, we tried several different Cat 5E cables, both self built and mass-produced. Same behavior. Re: Speed/Duplex, this problem initially surfaced due to a customer. They had our product, in some instances, over 150' away from the switch. Their installation of 6500s...
  2. AndrewAllen

    Weird Cabling Issue: Cat65xx+x6148-RJ45V & x6348

    I have a 6509. In it are some 6148 line cards and some 6348 line cards. Most devices I connect to those cards that are more than 160' away will not establish a link at 100/Full. 10Full or Half or 100/Half works fine. Now, I plugged an old 6248 in there and it handled all 4 permutations well into...
  3. AndrewAllen

    Problem with Large (40MB) File Transfer on Sup720

    Has anyone tried moving a 40+ MB file from the flash of a 6500 catalyst running a sup720? I am having FT completion problems. Does anyone know of any inherent FT problems when transferring large files from this Sup's flash card? I'm pretty sure its not the network in general. Its pretty clean...
  4. AndrewAllen

    Question regarding Show Version Field

    In show version, there is the following field that describes installed memory: cisco 2610 (MPC860) processor (revision 0x202) with 53248K/12288K bytes of memory. What are the "numerator" and "denominator" values listed? In this case they add up to 64MB, which is what is installed. But why the...
  5. AndrewAllen

    How Do I Upgrade the Bootstrap ROM on a 3640

    I currently have: ROM: System Bootstrap, Version 11.1(19)AA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) Is the ROM socketed? If so, could I buy a newer ROM? If the ROM is upgraded are there any gotchas? From what I can tell I can't update it with the same mechanisms I use to update IOS versions...
  6. AndrewAllen

    How Do I enable TFTP service in TI After NetBoot?

    Rick, Unfortunately (in this case) I work for an all Mac shop so I can't use SM. I do like the direction you are going with the config file. The one I used was the 132 byte job that comes with the distro. I will try again with a config already set up with TFTP active. I'll report back here...
  7. AndrewAllen

    BayRS: What the heck is "set_protocol wfTftpLoad"?

    Inside of my inst_arn.bat file I see: :IP_CONFIG: echo "" # Load IP + ARP Protocols. set_protocol wfARPLoad set_protocol wfIPROTOLoad set_protocol wfSNMPLoad set_protocol wfTFTPLoad I can't perform this outside of the batch file. Is this loading some module from the arn.exe? Andy Ford Austin
  8. AndrewAllen

    How Do I enable TFTP service in TI After NetBoot?

    Rick, To answer your questions: 1. I did not try that, actually. Based on the "TFTP Service Not Active" message, I did not focus my efforts in the ICMP area. I'll check that out. 2. config.exe ? Are you referring to the "config" file that my ARN boots from in addition to arn.exe? I don't have...
  9. AndrewAllen

    How Do I enable TFTP service in TI After NetBoot?

    I NetBooted an ARN running 14.20r5 for both its image and config. The Netboot went ok and I logged in to the TI. A dir showed nothing on Flash, so I attempted a tftp get and was told the TFTP service was not active. I issued a set wfTftp.1.0 1 and I was still told TFTP service is not active...
  10. AndrewAllen

    What is configuration rollback Best Practice

    I am trying to set up some corporate guidelines around this. at present, I think there are three ways I could rollback a configuration to an earlier version Have an earlier version offline that I send to the router's flash and then reboot Could simply do a copy start runn if the running config...
  11. AndrewAllen

    BPS 2000 Text configuration: How do I create?

    Nicolas, Thanks for the FYI. They should have just waited until 3.1 to include the command to read in the text config. [thumbsdown] Andy Ford Uplogix, Inc. Austin
  12. AndrewAllen

    IP Address and Manager Password BayRS MIB entries

    Two MIB questions: 1. What obj.attr pair do I need to find the IP address entries for my various interfaces. I have perused wfCSMACD, wfIf, wfIP, wfCct, etc. 2. I know it is encrypted, but in what obj.attr location does the Manager password live. Thanks, Andy. Andy Ford Uplogix, Inc. Austin
  13. AndrewAllen

    BayRS Default TFTP Timeout during transfer

    Hello again, does anyone know what BayRS's default timeout is once a TFTP transfer has begun? Ie, how long between packets before the router gives up and aborts the transfer. thanks, andy Andy Ford Uplogix, Inc. Austin
  14. AndrewAllen

    BPS 2000 Text configuration: How do I create?

    Ok, I have a BPS2000 running BOSS 3.0.0.54. In CLI, there is a "config network" command that the docs say will load an ASCII config, via TFTP, into the switch. Where does this config come from? I can't find a command to SAVE a text config, only READ a text config. Is there a known format for...
  15. AndrewAllen

    How Do I: Shutdown an ARN interface in TI?

    To quote Mr. Spock: "I, am a fool." I was so hung up on Gets and Sets that I apparently overlooked the most obvious command in the TI inteface: Disable and Enable. Sheesh. Well, thanks. I'm doing some "expect-ish" stuff in JavaScript and needed to enable and disable an...
  16. AndrewAllen

    Can I: Use XMODEM to transfer configs and OS files?

    Is there anything in the BayRS world similar to Cisco's ROMmon mode? For example, if I had an ARN that had a couple of corrupt OS files and wouldn't boot, is there a boot helper cli that would either allow xmodem file transfers or tftp boot setup? What diagnostic/recovery options do I have via...
  17. AndrewAllen

    How Do I: Shutdown an ARN interface in TI?

    Doing it in BCC is simple. However, I need to do it in TI. I haven't found the wfxxxxx obj.attr to set. According to MIBdepot, wfIfEntry.7 (Admin Status) is read-only. When I disable via BCC, that attribute changes from up to down. Is there a way to set it via TI or is there some other wfxxx...

Part and Inventory Search

Back
Top