Search results for query: *

Thanks to all! I have contacted our support service, as suggested, because seems to be a severe data corruption. MP -- BLOG @ www.zerozone.it

Hi all, i've already enquiry the forum but without any result. I'll try again. I'm managing a MD110 BC13 with 16 LIMs and i'm expecting faults since few weeks. Here's what happens: <EXTEE:DIR=2875;EXTEE:DIR=2875; SURE? (YES/NO) <YWAIT WAIT WAIT WAIT FAULT INTERRUPT MESSAGE FROM OPERATING...

...005, LAST HIREI: 07:57:01 10OCT18 TIME DATE ERROR CODE 08:32:55 10OCT18 H'18 ADDRESSED UNIT NOT LOADED ENTER SWSW B-LEVEL SIGNAL *************** (H'005C) FROM OCM (H'017) EXE A IN LIM 001 TO ****** (H'002) EXE A IN LIM 005 NUMBER OF DATA BYTES IN SIGNAL = 4...

Hi all, i'm expecting strange behaviour of my BC13 MD110 system. When i did an EXTEE of any extensions, i got: <EXTEE:DIR=xxx; SURE? (YES/NO) <YWAIT WAIT WAIT WAIT FAULT INTERRUPT MESSAGE FROM OPERATING SYSTEM: RELOAD REQUESTED RELOAD REQUESTED SYSTEM INITIATED DATA < Sporadically i got...

...16 PU-NO PU-NAME PRODUCT NUMBER REV PATCH END then blocking LIM 16: <BLLTI:LIM=16;BLLTI:LIM=16; SURE? (YES/NO) <Y ****** WARNING ****** LIM IS NOW BLOCKED BUT THERE MAY BE EXISTING TRAFFIC EXECUTED and then remove from ecosystem...

Hi all, on an MD110 BC11SP13 i need to configure a short number (1555) that redirect to an external destination (geographic number). So, calls 1555 should be redirected to xxxx.xxxxxxx. Any hint how to do this ? Thanks, MP -- BLOG @ www.zerozone.it

...ACTIVATED NOT SIGNALLING NO CLOCK CONTROL SIDE 0 ALARM 0010 0000 0000 0001 GSMINPUT 11111110 ERROR RATE LIM TO GS SIDE 0 = 5*10EE-5 ERROR RATE GS TO LIM SIDE 0 = 5*10EE-5 SIDE 0 CONFIG: GJU_G WITH INCORRECTLY CONNECTED GJU_D LINK Maybe i did some...

Just for future reference, i add relevant entries on NUMBER CONVERSION DATA table with NUTRI; -- BLOG @ www.zerozone.it

...have some external destination connected to a VoIP system through ISDN trunk. DID was 4 digits for all. When internal calls occours, all works fine *but* when there are incoming calls to some external destinations, DID was sent fully and not "chopped to last 4 digits. This occours only for...

...i got a class 4 error: CLASS: 4 101 FAULTY CLOCK PROCESSOR DATE TIME ALP NOIF EQU INF1 26FEB18 12:10:20 1 1 002-0-**-** 1 following Alex, i checl LSU and then i want to the PBX to check LSU board. The only spare part i have is a R11 (installed, and maybe...

Thanks, i think i've solved with: KSANE:ADN=11190; KSDNC:DIR=3490,DIROLD=2290; SUDIP:DIR=3490 KSANI:DIR=3490,KEY=23,CAT=5,ADN=11190; SUDIP:DIR=3490; SUDIP:DIR=11190; -- BLOG @ www.zerozone.it

Hi all, i need to change number (at the moment is 2290) to the following phone: <SUDIP:DIR=2290;DIRECTORY INFORMATION AT 10:42:29 15DEC17 DIRECTORY NUMBER : 2290 TYPE OF DIRECTORY NUMBER : DTS EXTENSION TERMINAL DATA EQU TERMD ADN CALALT 2-1-62-14 0021 1...

After further checks, while trying to get CDR via FTP, i got: * Connected to xxxxx port 21 (#0) < 220 172.16.41.187 pSOSystem FTP server (NTL68K/1.0.4) ready. > USER xxxx < 331 Password required for xxxx > PASS xx < 230 User xxx logged in. > PWD < 550 4.0/ > PASV * Connect data stream passively...

Thanks for your kindly help. But i've not REU nor RG5DC in this lim. Maybe the PU4DC ? And can i replace the PUA4DC with a RG5DC ? Michele -- BLOG @ www.zerozone.it

...REL 13: CLASS: 4 102 POWER FAILURE DETECTED BY DSU DATE TIME ALP NOIF EQU INF1 INF2 25AUG17 08:31:45 1 1 005-0-**-** 0 4 Looking on further posts, i've tried removing all TLU29 boards *but* alarm still there. At the moment, on the LIM there are PU4DC...

<EDFIP; FILE ADMINISTRATION FILE STATE DEV DEVICE STATE PRIO SMDR ACT SI-0 SIU SYSTEM BLOCKED C END < -- BLOG @ www.zerozone.it

...278 CIL DATA LOST FOR ONE OR MORE OUTPUT UNITS DATE TIME ALP NOIF UNIT EQU INF1 24AUG17 10:35:42 3 1 CLOP 004-*-**-** 2 278 CIL DATA LOST FOR ONE OR MORE OUTPUT UNITS DATE TIME ALP NOIF UNIT EQU INF1 24AUG17 10:36:17 5 1...

Thanks for your prompt reply. Following flow diagram, seems to be nothing dangerous. So, i clear errors log and waiting for another (hoping no) error. Luckly, there's no ext linked to that LIM. Michele -- BLOG @ www.zerozone.it

...07:35:12 06MAR17 H'41 INTER LIM SIGNAL LOST - MISMATCHING SEQUENCE NUMBER BRANCHVALUE = 00005EFF ENTER SWSW B-LEVEL SIGNAL *************** (H'0000) FROM ****** (H'000) EXE A IN LIM 013 TO ****** (H'000) EXE A IN LIM 003 NO DATA IN SIGNAL TIME DATE...

...SOFT PARITY ERROR IN LIM PROCESSOR MEMORY. DATE TIME ALP NOIF UNIT EQU INF1 INF2 03MAR17 11:54:17 3 1 RMP 003-0-**-** 0 0 RDATE RTIME 03MAR17 11:54:17 What it means ? And what i can do ? Thanks a lot, Michele -- BLOG @ www.zerozone.it