Search results for query: *

thread798-914765 Hello, I have the same problem as described in the thread 798-914765. It ends with a PM. Can I know what the solution was ? CALL SERVER/MAIN CAB VERSION 2121 RELEASE 3 ISSUE 00 + IDLE_SET_DISPLAY NORTEL IN-SERVICE PATCHES : 43 PAT# PRS/CR PATCH REF # NAME...

The meridian t1 is connected to a patton gateway (patton smartnode 4970). This gateway is connected to the 3cx thru the network (rj45). Thanks.

You are probably right. I just imagined that is was wider :)

Just to be more precise, I use a TMDI card in my cabinet for the t1. Under the cards, there are ports where cables run out. Since my card is in slot 2, I use the cable at the bottom of the cabinet that is connected on port 2. That's where the cable that ends with a db25 is connected.

From the pbx, there's a cable that connects to the bottom of the card and ends by a db25 connector. On that connector, there's a db25 to rj45 adapter. I run an ordinary cat6e câble to a patch panel that goes to another one and from that one I go into the rj45 port on the back of the patton. Thanks.

I was able to finally configure everything properly. For future refence, here is my config to connect a meridian opt11c with a 3cx system using a patton smartnode 4970. I have used 3cx's provisionning to configure the patton. Patton: Modified the e1t1 config to this: port type: t1 port type...

Targ is ok. I have tried ISGF with tie trunks. I can dial outside now ! But I have 2 other problems: No more caller id on this route and when I dial from outside, i get to the automated attendant and when I trie to dial the extention on the 3cx side, the systems says that I cannot dial that...

I have all of these. But what kind of interface I need to configure on the 3cx end ? The options I have are: NI2 - DSS1 - NTT - DMS100. The problem with DMS100 is that I cannot put it as "net" side on the 3cx and I can't put it on "net" side on the Meridian... Thanks.

How do I find out ?

I get an error if I do that. Marco

Sorry, it's CBCR not CRBC. In the administration manual, it says: Service route indicator Thanks.

I see the CRBC prompt in ld 16 right after I put IFC = NI2 for a TIE trunk type. I have no clue how to configure ISA routes. Thank you.

My NCOS is the highest it can be ( I don't want to block anything outgoing ). I have turned on the trace and I see all the digits (I put the 9 on the 3cx side). I have found what is happening: my calls are going to the attendant extension instead of accessing bars. How can I change that ...

Hello, I have succesfully connected my 3cx phone system to our meridian using a TMDI card / PRI / NI2 protocol / DID trunks. Everything is working fine except for 1 think. If on the 3cx side, the user dials an external number, ex 91234567890, it never gets out from the meridian and will ring...

@StanleySteamer Yes that is correct. My TARG on the route is 1, the TGAR on the trunk member is 1 and the TGAR on my phone is 2. I tried changing the TARG on the route to 0, I also tried changing the TGAR on the trunk member to 0 but unfortunately it doesn't work. I have abandoned the idea of...

I have succesfully configured an analog port (type:500) that can communicate with the gateway. I would have liked to use an analog trunk instead because it can pool lines and I don't have to specify each extension. Is there a way to create a route with some analog extensions ?

My analog trunk as TGAR 1. All the other trunks except one has TGAR 1 as well and they are working fine. Thanks for the CLID info !

How do I set that up ? Never heard of that. Thanks.

The VOIP is a 3CX. The gateway I'm using is a Grandstream GXW4108.

A busy signal