Search results for query: *

Since a long time ago, I know the Delta Server miss authorization codes after a server restart. I mean, the calls data continues being recording, but the auth. code does not. They are registered again only if the windows register is modified. Does someone in this community knows about a...

In accord with documentation a daughter trunk card installed on an analog phone card should connect the first trunk to the first extension in the case of power failure. In another source it is indicated the fourth trunk is connected to the last extension. On my installation, neither of this...

I had set a SSID in the 7921 which I known is a valid network, but the Survey option in the phone never appears to detect the network. I know the Wireless network doesn't have any security applied. Daniel Escalante.

I had been advised that it is possible to use third party access points (non Cisco) no get the 7921 IP phones registering to the Communications Manager Express. Can somebody give some tips to test this functionality? I had tried with a Linksys WRV200 (actually a router) and a 3Com AP (sorry, I...

I already test with the IP address defined in the manager. The phones indicate password error unless I set the gateway address (192.168.1.254)

In accord with the last configuration I have, all over 60 IP extensiones have Direct Media Path unchecked and codec G729. If I set an address different to 0.0.0.0 the phones doesn't register and indicate password error. I find if I match the IP address in the phone and Manager, the registering...

In most test, I did't get an error message, the 2nd phone just display the extension number, but the line is dead. If I check the IP Phone status in manager, I see the extension number indicating the phone type is unknown. In other cases the 2nd phone indicates just for a moment the new...

Yes, tlpeter, the phones are set as you indicate. The very extraneous situation I saw in the Monitor was that the remote extensions appear to be registered with the gateway address (192.168.1.254)instead of IP phone. Today I recreate a lab environment using an smalloffice and two linksys...

Probably my first explanation was not clear enough. Obviously I have two different IP addresses in the phones (172.16.10.11 and 172.16.10.12), but they are getting access to the IPO through the same VPN and gateway. So, the IPO reports two extensions registering with the same IP address...

I can't register two remote extensions through a VPN. Only one or the other register and work but not both. This is my environment: 5602/5610 -> LinksysRouter -> Internet -> Fortinet -> IPO406V1 Three months ago I set up the VPN between Linksys Router and Fortinet Firewall, and the 5610 had...

Thank you very much, however this document is old and don't have commands like AT-DEBUG, AT-ERASEALLSECURITY, etc.

Where can I find ALL AT commands supported by IPOffice 400 & 500 series? Thanks in advance.

First of all, I made a mistake my IP phone was 4606 not 4402 as indicated above. It appears the problem was solved using a 5610 phone. 4610 also present similar problems. Now, what can be different in the IP behavior whit these phones?

If the phone indicates "Discovering ...", it means the phone is searching for the PBX, although the router is visible. I think you lost the VPN connection, you should verify it before unplug and replug the phone. While your phone keeps connection to the ethernet switch, you will never see "No...

1. The equipment has 20 VCM channels. May be it is important to know that the system has over 70 IP local extensions. 2. I don't have a line group for the IP line. I'm not linking two IPO equipments, just one remote extension. 3. SSA is not supported because the system is version 1. Anyway I...

This is my environment: IPO --> LAN Switch --> Fortinet 100 -->Internet -->ADSL Modem --> WRV200 Linksys Router --> IPPhone 4402 I have a VPN created between Fortinet Firewall and Linksys Router. The remote extension registers normally in the IP Office 406 V1(3.2.54). The extraneous problem is...

The last CCC available release is 5.0.43 which includes Delta Server 5.0.40. still have the problem although the Technical Bulletin # 81 indicates this issue had been fixed, CQ32894.