Search results for query: *

Hello, I have an ASA5510. Whenever I setup a new Windows VM I add the IP to the access-list and allow access to port 3389. I also create a new static map. I'm going to build out a new ASA and I'm wondering if I have to add each IP to the access-list or if there's a way to just open port 3389...

Hello, I have an ASA5510 configured that allows direct RDP to some servers. I'm only able to connect to the internet with servers that have a static map. If a server does not have a static map I'm unable to do so. I would just create one but I've run out of available public IPs and I actually...

That was it unclerico! Once again you come through for me. It's greatly appreciated.

Hello, I've created a site-to-site connection between two ASA5510s. The tunnel is up at both ends (as shown at top below). However, I'm unable to ping across and I can't join a domain controller in Site A to the domain in Site B. I'm sure it's some simple command that I'm missing. An extra set...

thanks for the reply brian. i've made the change but still no luck.

Hello, I'm trying to allow RDP access through my PIX to a server. I've done this many times (add ACL and static map) but for some reason I cannot get access through this particular PIX. The difference between the ones that work and this one is that with this one I have a VPN site-to-site...

First of all, thanks for the quick replies unclerico. Here's my current config. So I need to add a new static map with the new IP address? My existing domain is 192.168.48.x and I want the new one to be 192.168.50.x. So my static map should be 209.xxx.72.z (where z is what?). Thanks! ASA...

I have some additional info. It doesn't look like they ran a new cable. Here's what they said: "There's no new network cable. The ip is routed to the existing network interface." Is this what you're refering to? Thanks unclerico.

yes they are unclerico

Good afternoon, I'm wondering if this is possible and if so where can I find the steps to configure it. I have an ASA 5510 configured with Eth0/0 as my outside interface (209.xxx.67.xxx). Eth0/1 is configured as my inside interface (192.168.48.1) I have Eth0/2 and Eth0/3 open. I ran out of...

Sorry, I have several other PIXs that have VPN working that do not have an acl allowing 10000. I was using them as an example. I'm trying to connect to this PIX using a Cisco VPN Client (version 5).

I also added... access-list 101 permit tcp any 10.100.10.0 255.255.255.0 ...and I'm getting the same error

Thanks for the reply North323. I have several other PIXs that work and none of them have an acl for allowing tcp 10000. So should I add: access-list 102 permit tcp any host 209.xxx.xxx.xxx eq 10000

Good morning, I've run through the Cisco remote VPN setup guide I have but I'm still unable to establish a VPN session. I have a PIX 515E with ver 6.2(2) Here is my config: PIX Version 6.2(2) nameif ethernet0 outside security0 nameif ethernet1 inside security100 nameif ethernet2 intf2...

Good afternoon, I have an ASA 5510 that is remote VPN enabled. Everything works fine. However, in the past month I've had to reload/reboot the device because people no longer could connect via VPN. When this happens I'm still able to ping it, SSH to it, mail flow to my Exchange Server is fine...

Hi Brian, I'm running 6.3(4) on two of them and 6.3(5) on the other two. I will see what I can find on 'hairpinning'. Thanks for the help.

Hello, I'm not sure if this is possible or not and I'm sure one or more of you could tell me if it is. I have 4 sites where each site has a PIX 515E. They are all connected via site-to-site VPN. Internally I can connect from any of our 4 offices to resources at the other location. I would...

Hi Brian, Thanks for the response. I found an article that corrected my problem. When I was setting the clock on my ASA I was just entering the time and date. After I entered the time zone and some daylight savings entry it worked fine. Rob

I am unable to connect using a Cisco VPN client to my ASA 5510. When I try to connect I get "Authentication Rejected: Clock skew greater than 300 seconds". However, the clock on my ASA and on my Active Directory domain controller (PDC time server) are the same exact time. As is the laptop I'm...

Hi Brian, I'm not sure I understand what you're saying. Thanks.