Search results for query: *

You probably could do this using a Forwarded Routing Rule in Unity Connection so that calls forwarded from the hunt pilot number will get routed to the pilot number for the call handler that provides the auto attendant function....

You can do this using IP-IP Gateway feature ... or CUBE .... SIP >>>>> SIP Inbound dial peer >>>> H323 dial peer >>>> h323 voice service voip allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip

If you have access to hardware inexpensively, building a home lab, or something at work if possible, will provide greatest flexability...but financial resources may lead to rental of rack time. INE or IPExpert both have racks for rent .. may or may not be less expensive depending on how much...

Unity 5.0 ... Server A and Server B ... user added on Server A cannot be found when looking for Subscribers on Server B. New user add on Server B can be seen on Server A .... Seems like something not working in one direction for user replication ... ?? Fixed SQL job errors due to user...

Check ATA-186 documentation online .. go to Parameters and Defaults ... look for Ring Cadence ....

Try this: voice translation-rule foo rule 1 /384427/ /0115554443333334/ voice translation-profile Intl translate called foo dial-peer voice 222 pots destination-pattern 384427 translation-profile outgoing Intl port 1/1:23 Should get your international number sent...

The digits that get dialed are in the Called Party Transform Mask ... along with any Prefix Digits you may need.

Thanks . this was first attempt at log in after initial install and config of the mailbox. I just changed the password and can get in OK now .. but was trying to figure out if there is a set default value when the Unity is first installed and mailbox first configured.

Thanks again ... that didn't work either....

Thanks.... tried 12345 and that did not work.

Anyone know what the initial User PIN on a mailbox is if the user template is not modified? Default behavior is to have user enter PIN on login and then have to change it. Just trying to figure out what the initial PIN defaults to if not deliberately set before configuring user mailboxes...

At the bottom of that drop down list of numbers you should see "----More Options----" ... If you select that, it will bring up a box where you can search all available user numbers.

If these calls are coming in on different circuits, you could prepend a unique digit(s) on the called number and then use that to route accordingly. If they are coming in on the same circuit, then there really is no way to know which 67676 was called is there? You would need to get the telco to...

Wireshark for sure! CUCM provides tools for looking at CDRs, etc. Real Time Monitor Tool (RTMT) provides some visibility to what's going on ... CUCM traces will give good info also ... there are tools for reading the traces .. Voice Log Translator is a good one. Triple Combo works too .. but...

Can you ping the inside phone from the outside phone? On the PIX firewalls, had to do an h323 protocol fixup..this allowed the firewall to do a deep inspection of the signaling messages to get the port numbers that were to be used for the audio stream..since signaling and audio are on diff...

debug isdn q931 on that gateway should tell you where the disconnect is originating..

What does RTMT show for CPU usage on the servers? Any delay in getting dialtone, etc.? CUCM traces are showing that the phone unregisters...that happens because of communication issues between phone and CUCM server. Sniffer on the LAN? See if something is running amok .. virus, etc.? I've...

The FXO port has no way to signal that the call is disconnected when the outside caller hangs up before the call is answered. A common fix is to reconfigure the port as ground start vs. loop start. Requires coord with the telco. You have supervisory tone disconnect anytone..so if you can get...

This shows that the phone lost it's LAN connectivity to CUCM: 2254: WRN 12:50:54.032446 JVM: Startup Module Loader|cip.sccp.cn:? - Socket Timeout exception: cip.io.SocketTimeoutException: Connection timed out: Connection timed out Close(d) Connection ..., errno=145 Check the...

Which version of Callmgr???