Search results for query: *

So I cannot figure out where the extension ranges are configured in my Xpressions server.. I have certain extension ranges within my OS4000, that when I build an Xpressions mailbox, the entry for the message waiting signal and the voicemail (*) are populated with 1+ my local area code and not...

Red alarm means your span is down, the card is not seeing any incoming framing or connectivity from the distant end. Put a loop back plug at your demarc and see if the circuit goes green. If it does go green, then you are good to your dmarc. If it is still red, then you have a problem at your...

Thanks for the reply., I was trying to post a screen shot, but the upload image wasn't working... I finally fixed it.. I'm not sure how I broke it, but the fix was to click on the history window tab and drag it slowly down to the command line window, and then it expanded back to the usual place...

So I managed to mess up my Com Win screen somehow, and now instead of the history window popping up just above my command line, it's been resized and shows up in my command line and also appears with the blue tab at the top of the window... I cannot figure out how to get it back the way it used...

Worked like a charm... Except that when I deleted the TDCSU from the Cornet Trunk group and re-assigned to my new Cisco trunk group, my Cornet calls started failing... I discovered separate LDPLN entries that had routes for each STMI in the trunk group??? There were LDPLN entries for the...

Great Info, Thank you! Yes, I still have 3 other STMI's in the trunk group (this side was way over trunked ) so my plan is to delete the TDCSU and then create the new Trunk group, then add the new TDCSU... I think I have a good handle on this thanks to your help...

I'll give it a go.. Mostly same config, but new trunk group, new extension range in WABE. The existing numbers to the other 4K which is remaining, have a DAR of STN and point directly to the DEST NO.... I'm pulling this STMI from the trunk group and creating a new group for Cisco. Should I not...

Thank You Moriendi, That almost sounds too easy... So I would set the extension range in dial plan (WABE, I know, I can't stop calling it dial plan) to a DAR of TIE and then create the LDP to point to the route and the route just points to the trunk group?? Since these are currently SIPQ, when...

Nevermind, I just remembered the destination Gateway is the one that the call routes point to... Not the gateway in my switch....

Yep, they do not trust anyone... It's like the NSA here. Good Times!

I am going to be utilizing an existing STMI that is currently configured for Cornet SIPq - If I use a SIP trunk profile in WBM, does that do away with the GKREG?? Just thinking I use GKREG to setup my LDPLN , LDAT, etc... If GKREG is no longer used, how do you point the call route to the...

Going to be configuring SIP tie trunks to a Cisco and was reading earlier posts about using the SIP trunk profiles in the STMI rather than GKREG.. So I have a question about a message that displays in the WBM when I click on the Cisco UCM profile. I see in red letters at the top "PROJECT...

Well, there are a couple of problems with that.. First: I do not have admin rights to any machine within the facility.. Second: If say I brought my own personal laptop to work which I could do the install on, once I tried to connect the laptop to our network, the network would not allow it to...

I'm getting the following error when I try to launch RTDS " javax.net.ssl.SSLException:Connection has closed: javax.net.ssl.SSLHandshakeException:No appropriate protocol (protocol is disabled or cipher suites are inappropriate) " It appears as though RTDS does not work with the latest version of...

Hi, Is there a way to change the default Operator for individual Xpressions mailboxes? I have a couple of mailboxes that I'm using as sort of a poor man's call processing box. The mailboxes are set to not accept messages, so when a caller has heard the entire greeting, the system prompts to...

Hi, I'm trying to configure a hunt group in order to have multiple phones ring at the same time when the main HG number is called. I would like to have the secondary extension of the phone (phantom exten) be the Hunt Group member.. For some reason though, the phantom extension does not ring...

been a really long time since I did 9005, but I think you could do a LI RP ALL in CNFG and it will display all of you configured digital ports... and a LI SLI ALL would do you analog stations...I can't believe I forgot most of the 9751 commands, I worked on that product just about every day for...

Thanks!!

I added some new Cornet trunks on an existing STMI board, and this message displayed after inputting the new TDCSU record. H17: CHECK THE AMOUNT OF DEVICE MEMORIES IN LTG 1 FOR D-CHANNEL CONNECTIONS, OTHERWISE INTERNAL BLOCKINGS MAY OCCUR ...

It's been a while since I did any software on the 150 / 3000, but if I remember correctly, you need to upload the "delta" changes to the system before you save the KDS file to your PC.. I think once you do a save of the KDS then you lose the delta option... In Manager, download your KDS from...