Search results for query: *

I set the inbound destinations to a page group with duplex intercom, auto answer. Could do both 89501 for duplex and 89401 to call the extension

I have 1 private and 1 public not sure it makes a difference from my testing FreePBX can dial 9 out over BCM and both can call extensions on both ends using private or public. It looks like theres just less SIP options using private. Did you find a way to not use dest codes when calling from...

I got inbound calls from BCM - FreePBX Setup an inbound route on Freepbx to accept 89xxx (dial out code on BCM - FreePBX) and routed to the corresponding FreePBX extension. I even got paging from BCM to FreePBX CallerID comes up on the FreePBX sets as anonymous. I have send long name setup on...

If anyone has screenshots for the setup of BCM extensions on the FreePBX side please post. Almost there, I'm just missing calls from BCM to FreePBX. Also noticed on the Cisco phones BFL for the BCM extensions shows "Red" offline but when pressed it dials fine. I'm doubting there's a way to get...

I got calling working from FreePBX - BCM extensions using the settings below. no prefix just dial 3xx from FreePBX and Nortel sets ring. I added each extension to the target line as "ring only" BCM - FreePBX intra calling not working yet. Working on that.

On the FreePBX side any string I dial out to BCM will ring the main ext 300. Calling in to FreePBX from BCM using the inbound routes above I get the FreePBX "extension is not in service" message on the BCM phone. :Solved. I needed to create a target line for each BCM extension. See target...

Up until last night I had "From Header Domain Match" and signaling was set to NONE I'll try changing to numeric IP.

Always on a Friday [upsidedown][pipe] These are my Voip.ms trunk settings. I turned signaling method from NONE to OPTIONS and incoming works now without having to dial out first. Slight delay in ringing in it used to instantly hit the BCM now theres a 1-3sec delay but at least calls are working.

"from-internal" should do it. I reverted most of my Freepbx setup yesterday trying to get inbound calls working again on the BCM but that was all I had different. I was had two trunks with two outbound routes "from-trunk" with no prefix, "from-internal" with prefix. From BCM I can dial 89+401...

Sorry for the confusion. Is DISA working?: DISA is not working. kept getting DISA invalid entry then AA played after. DISA is off now. Are the Door Phones working?: Doorphones are working Are all Voip Trunks working?: All trunks are working now that I set Nat pinhole options to 30, slight...

This post just saved me from resetting the BCM and starting over from scratch. https://www.tek-tips.com/threads/voip-ms-delayed-inbound-issue-with-did.1812521/ Changed ITSP “from header proxy address match” didn’t help. I turned signaling method on to “options/30” to give it a tap It’s...

Now having an issue where if I call in to the voip.ms trunks it hangs then disconnects no ring. If i use the trunk to make an outgoing call I'm able to make inbound calls to the trunk for a few minutes then its back to no incoming calls across all trunks. I have to make an outgoing call from...

Hey thanks for that! I changed 061 to auto answer DISA after that I cant call in to any of the voip.ms trunk lines. I managed to get one to work by reentering the target line pub rec # then when I would call in I would get something like "the command you entered is not valid" then AA as usual...

Update: If I dial 9+mobile number from the Freepbx Cisco 8865 will dial out on the Nortel trunks. Also will dial from any Nortel trunk if i put in the trunk code eg. 82,85,87. Those are seperate phone numbers for private lines. Still no DISA

I've been trying to get DISA auto DN without Cos to work for a bit. Not exactly sure where to route what. It's a little confusing. Bellow as per the BCM manual this is a tandem call but I'm not seeing detailed instructions on how to do it. "Answer with DISA cannot be administer to voice over...

Hahaha I like that diagram :) All they had to do was finish that one last bit and the BCM would live forever hahaha. I was thinking DISA. I was trying to get around DISA not working with VOIP. I'll try that and see if it works. Thanks (y) Its a small home system 20 ext's only 5 T7316E's the...

Hey Firebird, Thats great!!! All you have to do is delete the call ID from the outbound route and trunk in FreePBX. Let the extensions themselves forward the CID info eg. Front Desk <401> Sends the name First. I ordered a Pi4. which version FreePBX and what did you use to install it? I also...

Got the trunk registered :). Doorphones work perfect (y) I had it calling BCM-FreePBX when it was on "Public" using 89 to dial to FreePBX. I removed the public now I have "89" as dest digits in the private routing table it doesnt call out to the FreePBX. I also still don't understand how to set...

I have my dial patterns set up as 2xxx for BCM digital, 3xxx BCM IP Phones, 4xxx BCM hunt groups I tried using Outbound, Inbound, Send & receive. I still get not found from 192.168.1.245:5060 on the BCM

@daniel05 I cant get freepbx to register with the nortel using your settings. I get not found from 192.168.1.245:5060 which is the FreePBX