Search results for query: *

It might be just I didn't understand the term "renumber". It looked to me it is to logically move the slot/board number? But from other part it appears "renumber" is just to get the processor board to know what boards are there, correct?

5)In System Programming, do a Board Renumber What does this step do? It is necessary to move the new board to a lower number?

We have the following: Cabinet 1 0: Processor CKE5 1: 412 LS-TDL 2: 024 TDL 3: 016 TRR 4: 800 GL-ID 5: 800 DID Cabinet 2 6: Merlin Messaging Have never done adding boards. Do I just: 1) power all down 2) insert 024TDL to slot 7 3) power on 4) new board is recognized? 5) go renumber the 24 new...

Hi Thanks TTT. That worked for me. The dialer is mainly for some temperature sensor, not life threatening stuff so it is OK.

I clicked buttons 1 all the way to 20. 1: Ext Ring -I 2: Ext Ring -I 3: Line 801 -I 4: Line 802 -I 5: Line 803 -I All others are blank. It seems we don't a pool setup? I looked it over in "Quick Access" > Calling Groups > Lines & Pools tab (outside standard SPM). Did not find anything about...

...point before "press pool button": I don't know which one is pool button. The SPM screen is not the same as 4424LD+. The middle block has 5 buttons in a column on SPM but the phone has 6 buttons in each column. Also I checked manual found *35 is for "No ring" option. Not sure why it is needed.

Hi TTT, I was able to do the first part in standard SPM. I don't know where to do "Centralized Telephone Programming". Is it on the 4424LD+ ?

And we have 3 outside lines 801 802 and 803. I don't know about pool 70.

...to be done with WinSPM or Stardard SPM (which you launch from within WInSPM)? Then in Centralized Telephone Programming, press ANY button, dial *14, click on the Pool button, dial **14, click on the Pool button again and dial *35 Is above to be done at ext 100 (the special phone with a...

We have a 016 T/R board. Several analog phones are on those ports. Some of them needs to dial 9 to get outside line some get outside when they go off hook (w/o 9). How do I change the ones that require 9 such that they would get outside line by going off hook? I have working winspm but I am not...

...Service Observer: Service Observing Group: EXTENSION INFORMATION Extn SS/PP Type 110 2/ 1 4412D+ Button 34 *21 Blank Status None Button 33 *21 Blank Status None Button 32 *21 Blank Status...

Thanks. Adding 9 made it work for calls initiated from another extension. Did not work for outside calls transferred to that extension. So I did #80 to enter the auth code at the actual phone (although it has been said it is not needed), then it worked for outside calls.

@TTT it is in key mode. at the startup screen of standard SPM, bottom, it says "NAGIX Release 1.5 v6.0 Mode: Key".

...Service Observer: Service Observing Group: EXTENSION INFORMATION Extn SS/PP Type 110 2/ 1 4412D+ Button 34 *21 Blank Status None Button 33 *21 Blank Status None Button 32 *21 Blank Status...

on 3. I did: in SPM: sys program >> LineTrunks >> TT/LS Disc >> LS disconnect >> LS Reliable Disconnecting: Select One Yes is already red. I selected Yes again anyway and Enter, Back all the way out. Still the same.

Hi Tommy thanks for the response. you haven't allowed 1. RCF I did in SPM: sys program >> extensions >> Remote Frwd >> Remote Call Forward: enter extensions. Enter 222 and hit Enter. Does this take care of it? 2. and Trunk to Trunk for the extension I did in SPM: sys program >> extensions >>...

Update: Made some progress. Use #33 to enter forward number, at "forward to:" prompt, enter *13334445555# it is accepted by on the screen it only shows Forward:133344455 with last two digits cut off. Test calling and transfer to ext 222, got voice mail prompt. Never forwarding call.

...all the way out. Then I went to the 222 extension phone (4412D+), off hook SA mode, >> #80, at prompt for "auth:", entered 1234, accepted, enter *33 or #33, prompted for "Forward to:", then it failed. If I enter 1 area code etc, it cut off right after I entered 1 with an ambulance siren like...

Yes, I added the problem extension 103 to coverage group 30 and the problem is fixed. Thanks again.

Thank you merlinman. I checked the "details" tab of a working and a problem extension. It was the coverage group 30 (103 does not work. 102 works). I added those two problem ext to coverage group 30 now they work. Kudo! However I saw something that I do not understand. Before I added those two...