Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. NetworksMD

    EIGRP Routing

    Keep in mind that in EIGRP delay metric as stated above is a sum of all delays configured (either default or set through administration)on the interfaces to the destination network and not based on actual or real-time delay or traffic on the link.
  2. NetworksMD

    Spanning Tree vs Etherchannel accross just two switches

    I was just thinking out loud to myself (which I wonder is a condition I should post on another forum) if there would be any advantage at all to using two (or more) separate trunk ports and PVST+ versus just creating an etherchannel when it comes to connecting two switches together. I understand...
  3. NetworksMD

    What method does router use to forward packets....

    Routers forward packets based on the routing table and the best match found or default route. Depending on the protocol you are using, a router will look for a parent route match or a child route match for an ultimate route and then forward the packet out of the interface that is assigned to the...
  4. NetworksMD

    1 on 1 NAT and port forwarding not working...

    Just out of curiosity Cisco hardare is this on? It looks like you changed your default gateway from vlan101 t vlan1. Were your end devices always on VLAN1?
  5. NetworksMD

    Cisco asa 5505 simple admin help

    Another option would be to look draytek router and see what IP address is set for your default route or the mac-address table address table on your egress interface of your router and match that up to your ARP table for the IP address.
  6. NetworksMD

    Cisco router 7206

    If one router is capable of handling all the traffic in your network for a period of time should the other one fail (be it power supply or other issue) or you are willing to accept the degradation if one router is lost, you could argue that you don't need redundant power supplies in each router...
  7. NetworksMD

    Cisco router 7206

    If the single power supply fails (meaning the actual power providing unit transforing your power) you lose the entire router. In many cases in the IT world, especially in critical equipment you will have a redundant or even mutiple power supplies on devices.
  8. NetworksMD

    Cannot browse Internet behind ACL

    It would really help if you post your config. By the looks of your list it would look like something you put inbound on your internal interface (meaning traffic going into your external interface). If you apply this ACL on your external interface inbound it appears you want to be able to FTP...
  9. NetworksMD

    Statically Routing VPN traffic only

    It might be easier if you have a topology map you could post. However, based on your description above, when your users VPN into your site, your VPN device should NAT then to an internal address. It sounds like the internal source address for the VPN users is not defined you your routing...
  10. NetworksMD

    Avaya CMS Aux-in/Aux-out report design

    I have a request to see if there is a way to design an Aux-in/Aux-out report, by aux code, in CMS. The format would be the same as the login/logout report showing the user, and based on the date and the aux code selected, show the times the user went into and out of that specific aux code. Has...
  11. NetworksMD

    sanity check on route selection

    What is the ip address/subnet of FA0/0? If it is in the same subnet of the IP Address you are trying to ping (which I am guessing it is) then when you use a ping command directly on the router it is going to use the arp table or send an arp out on that interface, which I believe is why the ping...
  12. NetworksMD

    VLAN SETUP HELP?????

    I was thinking the same thing as Vipergg, don't think that linksys can support Dot 1q trunks or VLans. Make that port an access port on the same vlan(subnet) as the hosts on the linksys switch, and then on those hosts make your SVI for that vlan the default gateway for the hosts.
  13. NetworksMD

    Multilink Interface using e/0 and e/1

    Is the office a flat network that you are trying to set redundancy into layer 2? The other question would be what if your router fails? I have designed a remote office with 2 2811 routers with layer 3 switch modules and set up one SVI for each vlan on each switch, then set HSRP where every...
  14. NetworksMD

    Cell Phone locatin data

    Thank you for the info. In my particular call center application I was just hoping to identify the area code the cell phone is actually in or the state at the very least.
  15. NetworksMD

    Cell Phone locatin data

    I know that II-Digit information is available for use when someone calls into a call center with a cell phone, but has anyone had any success with receiving any data that would pertain to the location of a cell phone such as a tower BTN or region identifier? I had spoken to one person that...
  16. NetworksMD

    Broadcast Storm Control on 2948G

    I believe that the 2948 will support broadcast storm, multi-cast storm, and uni-cast storm control. It is set a physical interface or etherchannel connection. Go to a specific port and type "storm-control ?" This is also what makes it difficult to fine-tune. It can be set either as a...
  17. NetworksMD

    Cisco 3560 possibly stopping traffic to VLAN?

    Since this is only a 4 person office, I am assuming there is not a lot of inter office calling. If there has been are those calls being interupted as well? How is the voice traffic from the media gateway being routed externally or to HQ? Does the MG have any local trunks? If the route is...
  18. NetworksMD

    A very tough problem

    When you ping it our you using the IP address or Host Name? If you are using a host name does it resolve to the same IP when you are at the hotel and when you are at Starbucks? Also it's possible the ICMP is being blocked by the hosting company, so that there is no response for the ping and...
  19. NetworksMD

    New with Cisco 4507, Access List question

    I stand corrected, so ignore my post unless you are running an IOS lower then 12.2T.
  20. NetworksMD

    New with Cisco 4507, Access List question

    You can't remove a line from a numbered access list, you will need to recreate the access list with just the host you want in it.

Part and Inventory Search

Back
Top