Search results for query: *

I haven't attempted an archive yet as my main concern is dumping the memory to disk. EDD CLR returns the same EDD007 error.

Wow, thanks. Comprehensive! I have PDT access without error. I cannot mkdir on the c: in any folder level. My main concern is the stuff in memory that hasn't been commited to disk. I think the only way out may be a full TNB,CDB,SLT etc... dump and re-key after reinstallation. I can view the...

Hi All, Major issue with 11C running 23.35 Unable to run an EDD since.....February. It fails after the CONFIG tries to write to disk. ~~~~~~~ DB SEQ NUM = 3823 CONFIG EDD007 ~~~~~~~ Looks like we can't write to c:/u as LD 117 update data doesn't work either. There are obviously a lot of...

So the Polycom is registered as an endpoint in NRS or the SS? Dynamic or static registration? Sounds like a SIP keep-alive interval issue. If Dynamic, change to static. Have a look at the keep-alive settings on the Polycom if possible.

Hi All, I have an issue with zone bandwidth management for calls to multiple zones. Scenario: Zone 1 - Head Office Zone 2 - Main Office Zone 3 - Branch Office The WAN link between Zone 1 and 2 is 100MB The WAN link between Zone 3 and 1 is 10MB The WAN link between Zone 3 and 2 is 10MB...

Hi all, Is there anyway to stop all the LOG and QOS messages from displaying on the terminal when using telnet to a signalling server? I have a script that runs on prints some commands but the messages that spit out on screen are interrupting the data flow and it fails. If I could suppress...

Please can somebody explain this to me. Whenever somebody with a remote destination profile calls inbound to a route-point on the CUCM, from the same number that is associated to their RDP, we get a busy tone. As soon as I take the external number out of the RDP and call inbound to the same...

Hi, I have an issue where my server somehow is running with the RAID controller disabled (in BIOS) and where there should only be 2 drives (C and D) I can see 4 drives in Windows (C, D, E and F). I have 2 disks in the server. Now I need to enable the RAID controller and get the mirror back in...

Yep, I might try the re-seat/power cycle combo. Yep, using null modem adaptor for connection to the PC.

Hi all, I have replaced the octopus cable and even INI'd the switch but the 3 TTY's still are completely dead. I can Rlogin and have rebuilt the TTY's with no luck. The terminal settings are fine too as the same setup worked on this switch a week ago. Is there anything else I can try before...

Update DBS has no effect either. I don't think there is any way of escaping an INI

I have done an EDD after configuration. When you stat host in 117 i can see where the old IP address is coming from as it is still in the active host table, even if it is preceded with a -- for no active ID. So far only an INI has successfully cleaned this table and the SNMP trap source field.

What's wrong is that I don't want to do it to every single one every time. Have to schedule after hours INI and not forgetting the fact that 1 in x will go tits up. I forgot to mention that I am doing these remotely!!

Hi all, I have a problem that has occurred on every CS1KS/M rls 4.5+ (SSC, pure TDM) I change the IP addresses for active and inactive ELNK fine. Can ping, can Rlogin, all good.... Then configure SNMP traps. Alarms trigger traps correctly, I can receive them fine, but the trap states that...

As it turns out ihad to INI the switches for the SNMP / IP address settings to stick. They now work with no other configuration modifications other than a >reboot I am using CALL_SERVER as the device types for the 4.5's Thanks....

Hi all, I am tearing my hair out. I have a 5.5 system sending alarms to TM fine. Then there are two other 4.5 systems configured correctly but TM doesn't receive their alarms. I'm just looking for them in the Alarm Notification window. I have tried Meridian1, CALL_SERVER and even...

I see there is a TIM000 alarm that occurs every hour on the hour. I am planning to use this as an SNMP heartbeat. Can anybody tell me whether this alarm is only on recent rls versions or throughout >25.40 Cheers,

Hi all, Does anybody know of a way to tell if the SNMP alarm subsystem is still alive? Is there some kind of heartbeat alarm that I can receive by SNMP at intervals? I want something more specific than up/down ping monitoring. I was thinking of using the DTC001 alarm. Does anybody have any...

Just saw that spreadsheet of yours GHTROUT, and it looks perfect!! Thanks.

I need to automate alarm notification, matching the alarms to the help text. I am using HP OpenView to receive the SNMP alarms, but I want to match it with the help text and send out email notifications to customers.