Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. taliotta

    Unable to connect via Procomm on port 2 of Option 11

    I was able, until this week, to capture phone calls via Procomm connected to port 2 of the Meridian Option 11. It has stopped working. Procomm checks out on other connections. is there a command I need to make to turn on the printing to this port?
  2. taliotta

    BUG5327 help

    I found that in the manual, but have no idea what it means or how to read the resulting code after the BUG5327 message. Can anyone help me decipher the code.
  3. taliotta

    BUG5327 help

    I am getting this bug message on a frequent basis: BUG5327 BUG5327 : FFFF0019 00000019 00000004 00000004 00000000 00000000 BUG5327 + 105E63E4 10B17D9E 10B150E4 10B14AAE 10B149F2 BUG5327 + 10B13618 10B13252 10B1318E 10C7D9CE 10C7D7A8 BUG5327 + 10C7D65C 10C7D5F4 any help with decoding it...
  4. taliotta

    Upgrade advise

    I currently have a Meridian1, supporting about 120 extensions, with 1 digital and 1 analog card not used as yet. It is running Version 2111, Release 22, Issue 18. I have been asked by management to determine if I need to upgrade the hardware or software, and I would like an unbiased oppinion...
  5. taliotta

    Auto Attendent menu option

    Thanks guys, I figured it out. Just had to change the setting to CL and put the number in the existing menu.
  6. taliotta

    Auto Attendent menu option

    I have no problem getting into MM, I just do not know the steps I need to follow to config the auto attendent to forward the caller to an 800# when the number 3 is pressed.
  7. taliotta

    Auto Attendent menu option

    i need to set the auto attendent to dial an 800 number when the caller presses the nuber 3. I am at a loss, amy help would be appreciated. Meridian Option 11 version 2111 release 22 issue 18
  8. taliotta

    Using a laptop com port in place of my report printer

    I have an Okidata dot matrix printer on port 2 of the main cabinet of my Opt 11 system. Is there any way I can replace that printer by using a com port on a laptop via a communication program. I currently print out all calls made outside of the building and then have to manually sort through...
  9. taliotta

    DID extension

    Is there any easy way to list out all of the dial in direct extensions configured on the switch?
  10. taliotta

    Increasing RAID5 capacity

    Thanks guys. I have ordered 5 drives and will try it out next week. I will let you know how it worked out.
  11. taliotta

    Increasing RAID5 capacity

    I currenty have four 36.4gig drives in a compaq DL580. Can I remove one of the drives and install a 75gig drive to increase my capacity, then after it becomes part of the raid array can I then replace the other drives in the same fashion. Or should I buy an external raid array and use the SCSI...
  12. taliotta

    Allowing 800 calls to be dialed

    I'm fairly new at this. How do I modify the ncos table?
  13. taliotta

    Allowing 800 calls to be dialed

    I have phones that have been setup for internal extensions only, unless you know the 4 digit access code. I now need to grant access to 1800 numbers without using the 4 digit code. I can't seem to get a handle on this. Listed below is the configuration of one of these phones: DES 2014 TN...

Part and Inventory Search

Back
Top